Question about 1995 Ford Aerostar

1 Answer

HHO generator wiring

Would like to know where I would conect a HHO generator wire to the MAF sensor?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

The hho generator power and ground does not go to the maf sensor. what you need is a maf /map regulator, but it has no connection with the generator. it is just helpfull by saving gas if a hho generator is installed. If you have o2 sensors in the exhaust pipe, you need a EFIE first!!! more questions, no problem, hydrotuning@gmail.com, greetings, ****

Posted on May 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I disconnect output sensor where the wires r conected together


Need more info What output sensor? If you are talking about the pulse generator (output shaft speed sensor) in the transmission then the wires come with it. The output and input sensors com together.

Nov 11, 2014 | 2001 Hyundai Accent

5 Answers

MAF enhancer installed on wrong wire - engine codes


what does your MAF consist of ?
what did you get for instrusction?
is it just a resistor?
what are your troublecodes?
does the engine run fine without the enhancer installed?

Sep 20, 2008 | 2003 Volkswagen Jetta TDI

1 Answer

How do i fix trouble code 122 and 102


Throttle position sensor and maf sensor are displayed for these codes.Trouble Code: P0122

TP Sensor Circuit Low Input

Possible Causes:


TP sensor signal circuit is shorted to sensor ground.TP sensor signal circuit is open (except 1996-1998 models).TP sensor VREF circuit is open between sensor and PCM.TP sensor is damaged or it failed (it may be shorted).PCM is damaged or has failed.Trouble Code: P0102

MAF Sensor Circuit Low Frequency

Possible Causes:


MAF sensor element hot wire contaminated or the sensor failed.MAF sensor signal shorted to ground or ground circuit problem.MAF sensor wiring routed close to the ignition wires, generator, solenoids or electric motors.PCM has failed.Click on link to view how to replace.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80cb3c01

Oct 19, 2012 | 2003 Chevrolet Impala

1 Answer

What is the code PO102 on a 2002 Chevrolet Impala


code PO102 is mass air flow sensor circuit low frequency condition.what it is saying.MAF sensor element hot wire contaminated or sensor failed.MAF sensor signal shorted to ground or grounded circuit problem.MAF sensor wiring routed close to ignition wires generator solenoids or electric motors.PCM has failed.

Jul 14, 2009 | 2002 Chevrolet Impala

1 Answer

My HHO generator draws too many amps, how do i get the amps down?


1st thing to check is the electrolyte: Use white vinegar, NOT baking soda or lye. Use a minimum of 12 ga wire on all connections, and power the generator through a relay using a 30A fuse to feed a 40A relay.Install a Tap-a-line connector from the radio circuit of the fuse panel to the toggle switch, then run a 14ga wire from the toggle switch to the relay. Doing this ensures that the generator is energized ON LY when the ignition switch is turned on. The 12ga feed wire to the relay should connect directly to the positive terminal on the battery. The 14ga wire from the switch is used only to activate the relay. This way the relay carries the amperage to the generator, and it does not pass through the switch. If the amperage is still too high, use less vinegar and use more steam distilled water to lessen the concentration, therefore lowering the amperage draw. All the parts required for this hook-up can be obtained at AutoZone, Oreilly's, etc. Good luck.

Feb 26, 2009 | 2001 Dodge Ram 3500 Truck

1 Answer

MAP sensor wiring to ECU


There are 3 wires from the MAP to the ECU

Brown is E (Ground)

Yellow is VC to VCC (sensor to ECM)

Light Green with a Red tracer is PIM to PIM

Feb 09, 2009 | 1995 Toyota Corolla

1 Answer

MAF Enhancer


as in any electronic circuit there has to be a path to and from a componant. the ecm sends a signal along the red wire it will have a certain voltage parameter. the ecm is expecting a return signal of the same voltage if it doesn't get it it will either throw a code if there is no return voltage value or if there is but it is outside the parameters then it will adjust to compensate. there is no need for such an extender ring. the resister should be on the red(imput signal). please rate the solution.. thanks

Sep 21, 2008 | 2004 Volkswagen Jetta

2 Answers

Map sensor


What car engine?

Sep 03, 2008 | 1988 Daihatsu Charade

2 Answers

2002 ford mustang gt map sensor enhancer connection? (for HHO)


MAP enhancers usually wont do the trick for long - the computer will learn the adjustment to the MAF and overide within a day or so usually less than a few minutes.

The computer is best altered using an EFIE to adjust the O2 sensor(s), usually adding between .2 and .3 volts to the O2 sensor signals does the trick - each combo of the HHO and car is slightly different - you have to play with it to find your best setting. You only need to alter the signal on the O2 sensors ahead of the cats as they are the ones the computer uses to adjust the fuel.

Aug 12, 2008 | 2002 Ford Mustang

Not finding what you are looking for?
1995 Ford Aerostar Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...