Question about 1993 Chevrolet S-10 Blazer

2 Answers

How to change a starter

I'm having a problem taking it out.

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Expert
  • 92 Answers

A should be two bolts holding the starter, gen, chevy are vetical, frome bottom,before that is attemped, please remove positive cable from battery, then remove wires/cable from solenoid on starter,if this not accessable, you can drop starter, then remove leads, pls do not let starter hang by the leads if possible, thnku, good luck.

Posted on Oct 05, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

You have to get at these wires from the Wheel well wall! its almost impossible to drop the starter and get at the wires while it hangs!! Try undoing those wires from the wheel well wall and then drop the starter! but of course do disconnect the positive wire from the battery! also you may have to unbolt the Bell Housing in order to drop the starter without any issues

Posted on Jul 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001grandprix failed solenoid replace ment

Is that your starter solenoid if so some starters u can just replace it and some u cannot but your cAr is gm and should be able to change it u have to take the starter out to change it though

May 28, 2014 | Cars & Trucks

1 Answer

How to change my starter on the 2004 sienna

just take out the battery and you should have enough place.Its only three bolts for the starter,make shure you mark and take off the wires first.Or try from the bottom of the car.Take of the protection plate on the bottom

Mar 16, 2014 | Toyota Sienna Cars & Trucks

1 Answer

How to change starter

Take negative off battery post. Take off big end of cable from starter. and the small solenoid wire. Two bolts hold starter on (some cars use three bolts). Take them out and starter is free. Reverse procedure to install new starter.

Good luck.

Jan 08, 2012 | 1990 Acura Integra Hatchback

2 Answers

Starter makes a screeching noise sometimes just after the motor starts

Replace the starter before it ruins the flywheel. You have a worn out drive that applies to the flywheel. Flywheels are very very hard to change, in fact you can change 10 or 15 starters in the same time changing one flywheel

Jul 24, 2011 | 1997 Buick Century

2 Answers

I have replaced the starter and batteries and engine just clicks and starter gets hot

you have a faulty starter. you have to take it out.test it on the bench.
also check does the engine rotate ok.infect do this prior to taking the starter out.

Jan 11, 2011 | Ford F-450 Cars & Trucks

1 Answer

How to change the starter of my Nissan Altima

Thats a simple on...

Disconnect battery

Take wires off starter

Take bolts out of starter holding it to block.

Pull starter out.

Reverse to reinstall new starter.

Nov 13, 2009 | 1995 Nissan Altima

1 Answer

How do i change the starter in my 83 chevy caprice 305 without breaking studs on exhaust

the starter should come right out without taking the exhaust loose you may have to take a cover loose from aroud the starter at the transmission but you shouldn't have to mess with the ehaust at all

Nov 11, 2009 | 1983 Chevrolet Caprice

2 Answers

Can you tell me how to change the starter in an f150 1997 4 wheel drive truck I've cleaned the battery terminals and the starter wire ends from bottom of truck to the the starter. I have a new battery. I...

no special tools needed use a 1/2 inch or a 9/16 wrench for bolts but rule # 1 before you work on any electrical parts on your truck is to disconnect the negative terminal on the battery then take the starter off you 2 blots holding the starter to the engine take them off they maybe a little tight you my have use a little muscle once you take them out pull out the starter then you have to unscrew the cables use the same procedure to install I hope this information is of use GOOD LUCK

Jul 27, 2009 | 1985 Ford F150

1 Answer

How do i change the starter on a 1999 sr5 4runner

You'll need basic hand tools to change out the starter. The starter is usually held in place by 2 or 3 bolts. You'll need to make sure you note where the electrical connections go in order to replace them in the correct location following starter replacement. You'll have to get under the vehicle to replace the starter, even so, It shouldn't take more than an hour.

Feb 22, 2009 | 1997 Toyota 4Runner

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides