Question about Hyundai Motor 2004 Sonata

3 Answers

Turning signals dont work insead hazard lights come on

When we use our turning signals right or left the hazard lights come on it its place. Fuses seem to be fine. What could be problem. We know we may have a week battery that was draind.

Posted by on

  • issyrose Oct 04, 2008

    what relay do we check in the motor

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Check the steering wheel cover and pull the switch up maybe it the faulty one in this case. try toclean it using medical alcohol and a brush and try its might be stuck or its exposed to humidity!!

Posted on Oct 05, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Sometimes the problem is with the hazard switch. try turning it on and off and see if the problem would disappear.

tnx 4 using fixya,

drcool

Posted on Oct 04, 2008

  • francis rivero Oct 04, 2008

    have your battery recharged first so that we will eliminate the problem with weak battery. have a charger at home and recharge the battery to a good state before troubleshooting the problme with the signal light and hazard.

    tnx again,

    drcool


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 479 Answers

Check the relays and circuit breakers in the motors.

Posted on Oct 04, 2008

  • 3 more comments 
  • tech gurus Oct 04, 2008

    You might check your flasher relay which is under the dash

  • tech gurus Oct 04, 2008

    The Hazard system is a seperate circuit from the turn signals even though they use the same bulbs. I would replace the hazard flasher which should be located in the fuse box. I hope this helps you.

  • tech gurus Oct 04, 2008

    also Take the steering wheel cover and pull the switch up.... most likely your stuck.

  • tech gurus Oct 04, 2008

    or Try replacing turn signal flasher it may be faulty.

  • tech gurus Oct 04, 2008

    the relay is not into the motor.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Turn signal lights don't work


The first place to start are fuses, check your owners manual for location, typically left side of dash.

The emergency (hazard) flashers and turn signals are on separate fuses and run through the hazard switch. If all the lights work when the hazard switch is on then the problem will likely be a blown turn signal fuse.

Other possibilities are the hazard switch itself is bad, the turn signal switch is bad or a broken wire, all of which require a meter (or test light) wiring diagram and knowledge of the circuit to test it - better to have it done.

Robert Grove
Mobile Mechanic Malibu 310 651 8020 Auto Truck RV Mobile Repair...

Aug 09, 2014 | 2002 Chevrolet Impala

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

I have a 1987 chevy deluxe r10 dont have any turn signal I have head light brake lights park light an hazard lights but no right turn signal nor left turn signal I have check all fuses and put a new signal...


I think you might have a separate flasher for the turn signals under the dash. The turn and hazard flasher would look alike. Turn you hazards on and find the flasher for it under the dash. You will probably be able to feel it working and hear it clicking. The other flasher under the dash is for the turn signals. Try replacing that one. I think it was in later years they began to combine the two into a single composite flasher.

Mar 01, 2013 | Chevrolet Cars & Trucks

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

1 Answer

I have an 02 kia sportage. my signal lights come on but dont blink outside. no lights for the signal lights come on on the dash at all. also, no hazard lights.


If the 15A HAZARD fuse in the passenger compartment fuse box is OK, power is getting to the hazard function of the flasher unit. Pressing the hzard switch should cause the hazard lights to flash. HOWEVER, there is an electronic time and warning indication system module connected to to the hazard switch lead and that may be affecting things. If the 10A TURN fuse is OK, power is applied to the turn switch (with the engine in START or RUN) and you state you can select a right or left turn. HOWEVER, the RED/WHT and RED/BLU outputs from the flasher unit connect directly to the front and rear turn lamps and the instrument cluster turn indicators so you are not getting any flasher output. Again, that electronic time & warning indication system module could be affecting things

Oct 26, 2012 | Cars & Trucks

1 Answer

Turn signals not working, Toyota Tundra 2000


Hazards work only when lights are off. Left signal light stays lit on the dash and does not blink and is stuck on (lit up) when lights are lit. If I place hazards on while lights are on only right side flashes and whole dash lights flash too... I replaced the flasher relay and it still does not work. Suggestions anyone? Thanks!

Apr 30, 2012 | 2000 Toyota Tundra

1 Answer

Left and right signal doesn't work


Light fixtures are bad check with a light tester

Mar 19, 2012 | Chevrolet Cavalier Cars & Trucks

3 Answers

Im trying to change my fuses for my hazrard lights. on a G6 2006 poniac. i cant find it in the manual. don't really know if thats what you do, cause when i push the hazrard button they don't work.


This is not fuse, is an flasher, and maybe is integrated with hazard & turn signal module.

Also need review this RECALL

Hope helped with this. Good luck.

Nov 09, 2009 | 2006 Pontiac G6

1 Answer

Jeep - right turnsignal won't flash


Probably a bad ground on your front right signal, or a bad bulb. Try switching the right with the left, and see if the problem stays in the same place, or goes with the bulb.

May 18, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
Hyundai Motor 2004 Sonata Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...