Question about 2004 Chrysler Pacifica

2 Answers

Crankshaft Location I changed the oil in my vehicle and now I need to locate the crankshaft to reset.

Posted by on

  • 4 more comments 
  • sonny5052 Oct 04, 2008

    I am trying to locate the crankshaft sensor.

  • sonny5052 Oct 05, 2008

    After changing the oil a leak was discovered due to a faulty filter. I believe some of the oil got on the crankshaft sensor and I am trying to locate it to replace it.

  • breaking6 Nov 30, 2008

    Where is the crankshaft position sensor located on the 04 Pacifica 3.5L 2WD?

  • Anonymous Dec 07, 2008

    Where is the crankshaft sensor located on the engine

  • yadayada
    yadayada May 11, 2010

    There is no crankshaft sensor that can be reset, so what are you trying to do????

  • yadayada
    yadayada May 11, 2010

    The crankshaft is inside the engine, what are you needing to know??

×

2 Answers

I am just trying to locate the crankshaft sensor at this point.

Posted on Oct 05, 2008

I was told that there is a crankshaft sensor on the vehicle and I am trying to find out where it is located.

Posted on Oct 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of Crankshaft sensor on 2005 Dodge Caravan SE: 2.4 Liter. Is crankshaft sensor location the same as 3.3 Liter?


The crankshaft position sensor mounts to the engine block behind the alternator near the oil filter.

Jul 12, 2014 | 2005 Dodge Grand Caravan

1 Answer

Location of crank position sensor for 1999 ford windstar 3.8 se


Crankshaft position sensor is mounted on the engine front cover next to the crankshaft trigger wheel, below electronic ignition coil pack on transmission housing .

Mar 29, 2014 | 1999 Ford Windstar

1 Answer

Crankshaft location sensor 1997 vauxhall vectra estate 2.0 diesel


Wheres the computer on this vehicle fitted is it bolted to the inlet manifold by any chance? the sensor should be front right side level with the crankshaft ,not on the bell housing

Jan 09, 2014 | Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Where are the crankshaft sensors on a 2001 cadillac deville sedan?


The crankshaft position (CKP) sensor is a three wire sensor based on the magneto resistive principle. A magneto resistive sensor uses two magnetic pickups between a permanent magnet. As an element such as a reluctor wheel passes the magnets the resulting change in the magnetic field is used by the sensor electronics to produce a digital output pulse. This system uses two sensors within the same housing for the V6 engine, and two separate sensors for the V8 engine. The PCM supplies each sensor a 12-volt reference, low reference, and a signal circuit. The signal circuit returns a digital ON/OFF pulse 24 times per crankshaft revolution.
Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the air deflector.
  3. Remove the oil filter adaptor.
  4. Disconnect the crankshaft position sensor electrical connector.
  5. Remove the crankshaft sensor retaining bolt.
  6. Remove the crankshaft sensor.
zjlimited_1892.jpg

To install:

NOTE Inspect the crankshaft sensor O-ring for wear or damage. If a problem is found, replace the O-ring.
  1. Lubricate the crankshaft sensor O-ring with clean engine oil.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  2. Install the crankshaft sensor and the retaining bolt. Tighten the retaining bolt between 10 Nm (89 inch lbs.).
  3. Connect the crankshaft position sensor electrical connector.
  4. Install the oil filter adaptor.
  5. Install the air deflector.
  6. Lower the vehicle.
  7. Operate the engine and inspect crankshaft sensor for engine oil leaks.
  8. Perform the CKP System Variation Learn Procedure.
Hope helps.

Sep 20, 2011 | 2001 Cadillac DeVille

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

2 Answers

Where is the crankshaft sensor located ?


The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Jun 29, 2010 | 2004 Nissan Sentra

1 Answer

Need location of cranshaft sensor on 2004 cadillac


There are two crankshaft sensors located Center front of the engine, near the base of the engine oil dipstick tube.

Sep 25, 2009 | 1994 Cadillac DeVille

1 Answer

Location of crankshaft sensor


Hello mitchoreb: My name is Roger and I will be glad to help with your answer. You will need to raise the vevicle in order to see the sensor. Make sure to use safety stands when ubder the vehicle when raised up.Look in the area behind the oil filter.Just in front of the knock sensor.This will be just above the oil pan rail.The knock sensor is a round sensor with a round plug.The crank sensor should hove a oblong plug. You should have a picture along with this reply. Should you need any further help please just ask. Please rate the answer you received as this way we know you recived helpful information. Thank You for using FixYa.Roger8d42463.jpg

May 09, 2009 | 1998 Pontiac Sunfire

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica


can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...