Question about 2001 Buick Century

Open Question

1998 BUICK PARK AVE ULTRA CODE P0102 AND PO113

WHAT DO I NEED TO DO TO CORRECT THESE CODES?

Posted by on

5 Suggested Answers

  • 12 Answers

SOURCE: fuse box location on 1998 buick park ave

RIght hand side of the car behind a panel...3 clips hold it pull it off...Under the hood same side of car MASTER fuse box.....GARY KNOWS ALL ANSWERED THIS

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: 93 buick park ave Ultra. replacing water pump

Yes. Put a jack under the motor and remove 3 bolts from side of engine and the long center pivot bolt in mount and the 2 bolts that go top down into the frame and loosen the 2 bolts below mount. Jack up the motor until you can separate the mount, leaving the engine side in and removing the frame side. The engine side can be moved out of the way without completely removing.

Posted on Aug 08, 2009

Testimonial: "answered the question completely and thoroughly!"

  • 9 Answers

SOURCE: where is fuse box in 1999 buick park ave ultra

There are actually three fuse boxes. One is under the back seat.

Posted on Nov 02, 2009

  • 593 Answers

SOURCE: 1999 Buick Park Ave Ultra Service Engine Light

The code PO742 indicates the torque converter clutch is stuck on.
The torque converter is what connects the engine to the transmission.
It engages and disengages according to signals from the pcm, to aid in
smooth shifting. There are a couple of things you can try. make sure trans. fluid is full, if thats ok check the 20 pin connector, located on left
side of car on top of transmission bell housing. Make sure there's no
corrosion or bent pins. If this clears the code your all set, if not you may
want to ask your mechanic and see what he/she recomends.
Hope this helps.
Good luck

Posted on Jan 19, 2010

  • 44 Answers

SOURCE: Where is the a/c relay on my Buick Park Ave Ultra.

Hi

If your talking about the relay switch to your air conditioner. These are usually located under the hood, behind the engine and against the center rear upper firewall, in the fuse center. You have to remove the large black plastic insulator (that spans the length of the firewall), that covers the windshield wiper motor and other components, to expose the fuse center.
Pop the fuse center cover off and read the diagram inside, so you know which relay switch goes to the A/C unit.

Should you not find the relay in the engine compartment I recommend the following.

I own a 91 Park Avenue (same body style) and on many of these modules, there are additional relays behind the glove box. This is bit tricky to get to though. Because you need a Torq/star screw driver, and you will need to remove the glove comparment to get at them.

As always be sure you disconnect the negative cable from the battery before pulling any relays, to avoid shorting out your electrical system.

Good Luck.

Posted on May 24, 2010

Testimonial: "thx for the tip about the relays behind the glove compartment. I didnt know about those. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I save the radio code once I put it in It is a MICRA 2015 build


You need to be certain you are entering the correct code in the correct way to avoid being permanently locked out of the radio.

Different territories and models have slightly differing radios and the coding sequence can vary slightly. The vehicle literature pack should either contain an audio manual or the details will be found in the vehicle handbook.

Sep 21, 2016 | Nissan Micra Cars & Trucks

1 Answer

98 dodge ram 1500 5.9L 2wd codes P0300, P0301, P0302, P0303, P0171. What all do I need to do to resolve??


the p0300--p0301-p0302=p0303 are misfire codes and can mean needs tune up or wiring problem and p0171 is system to lean bank 1 with this code if you correct it will probably correct the misfire codes your receiving
http://www.obd-codes.com/p0171 Fixing Hesitating Car P0171 Code YouTube P0171 System Too Lean Bank 1

Aug 26, 2016 | Dodge Cars & Trucks

2 Answers

I entered radio code for my ford focus 2007more than 10 times now it's blocked. How do l reset it?


hold down the number 6 button on your radio for a few seconds and were it is showing the number 10 on the screen this should change to number 11 you now have three atempts to enter your correct radio code

Dec 05, 2014 | Ford Focus Cars & Trucks

1 Answer

Need Help


have a list of code and correct it one by one.
some error code have same correction.
need your patiences to do this.

Feb 20, 2012 | 2002 Ford Explorer

1 Answer

I get codes P0102 and P1128. My mechanic says I need to put a new mass air flow sensor on and it will take care of the problem. Is this correct?


This could very well be correct I believe code P0102 is the mass airflow circuit low input. P1128 should be a lean code.

I would first try cleaning your mass airflow sensor with a carb or throttle body cleaner, they have a tendency to get dirty and not read correctly.

Dec 13, 2010 | 2001 Volkswagen Cabrio

1 Answer

I have a 1994 volvo 850 GLT. Radio reset code


You will need to turn the ignition to the number 1 position and turn the radio on. It can take several hours, but the word code should come back on. When that happens, you will need to put the correct code in. If you don't have it, a Volvo dealer can give you the correct code from your VIN.

Jun 26, 2010 | 1994 Volvo 850

3 Answers

Need to input my radio code on 2005 Honda Civic


ok your radio displays ERR , OK 3 options let it sit for an hour turned on , to reture to CODE display , or pull the radio fuse out for a minute and put it back in , returning to the CODE display , or disconnect the battery for a minute , returning to the CODE display . you got the ERR display because the code was wrong or not entered correctly , make your choice of getting the radio back to the CODE display by 1 of those 3 choices , while the radio displays CODE , use the preset buttons , if the first number of your code is 4 , then press the #1 preset button 4 time , when the first number has been input , put the 2nd number in by pressing the #2 prest button , if 2nd number of code is 8 , press the # 2 preset button 8 times till the # 8 is displayed , and so on . you see where this is giong ? when you have entered all the numbers correctly you will have you radio back . when you say you have the radio code , good luck ! were rooting for ya .

J5

Jan 19, 2009 | 2005 Honda Civic

2 Answers

Radio code


If you don't have the radios security code, you can try entering 1111 as some replacement radios were coded with this security code. Your local Audi Dealer may be able to provide the correct security code for your vehicle, if you provide them with your vehicles Identification Number (VIN). This VIN is typically located on the drivers door pillar.

The radio should have a serial number on the unit which also can be given to the Audi dealer and checked in their data base of radio security codes. The serial number will start with AUZ, one radio serial number for example is AUZ1Z9A1965412.

To enter the code on the Wiesbaden Radio: Turn on the radio, SAFE should be displayed.
Push and hold the AM/FM button, then while holding the AM button down, push and hold down the SCAN button. Release the AM/FM and SCAN buttons, and the display should show 1000. Now enter the correct code using the radio pre-set station buttons (1-4). Button 1 changes the first digit in the code "1"000, Button 2 changes the second digit in the code 1"0"00, button 3 changes the third digit, button 4 changes the last digit in the code. In most cases the first digit is a 1 and won't need to be changed. You push each pre-set station button multiple times to step through the digits (1-9) to get the correct code displayed.

Code 1246 would entered by pushing button "2" two times, pushing button 3 four times, and pushing button 4, six times.

After entering the correct security code, push and hold down the AM/FM button, then while holding down the AM/FM button, push and hold down the SCAN button. The display will then show SAFE, release the two buttons, and now the radio should play correctly.

Sep 19, 2008 | 2001 Audi S4

2 Answers

Saab 900i 1992 model


I had a similar problem with my 94 Saab 900, I needed to reset the radio code because the one in my user manual was wrong. If you can remove the radio from the dash (you can buy a tool or make it with metal clothes hangers). Pop the radio out and the correct code will sometimes be written on the top of the radio.

Either way entering this correct code did nothing for me on startup. But the solution is far out - turn the ignition key to "on" without starting the engine so the electrical system is on. Then leave this for 1 hour. When you return the HID will display "enter code" (exactly like if you hold down the BAND button - but that doesn't work like this does). Now enter the correct code.

May 26, 2008 | 1993 Saab 900

Not finding what you are looking for?
2001 Buick Century Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...