Question about 1999 Oldsmobile Aurora

1 Answer

Electronic flasher trying to replace where is it?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Behind the cowling undre the steering column

Posted on Oct 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replacing electronic flasher

Are you looking for the flasher relay?It will be situated under the dashboard. Try operating the flashers, or hazard warning lights and listen for the clicking sound. The sound will lead you to the relay.

Nov 02, 2012 | 2001 Hyundai Accent

1 Answer

Electronic flasher

The flasher will be under the drivers side of the dash. You will need to remove the trim pannel from under the dash. The flasher will be above and to the passenger side of the brake switch.

Feb 17, 2012 | Cars & Trucks

1 Answer

We are trying to replace the electronic flasher relay in our 1999 Mercury Villager. Can you tell us where it is located?

The electronic flasher relay is located below the interior fuse block (Next to the hood release handle)

Feb 04, 2011 | 1999 Mercury Villager

1 Answer

Where is the electronic flasher located ?

  • Kneel down under the steering wheel .
  • Look up and to the right of the steering wheel at the edge of the vinyl molding for the dash ,you would see a screw holding it. But in reality, the screw is through a metal plate that slides over the top of the flasher unit.And the screw does not actually screw through the unit.
  • Remove the metal plate and you can see electronic flasher unit.
  • You can replace your old flasher with new flasher you have bought! and before you replace it,sandpaper the terminal ends. It would provide good connection if there is some problem with the connection.

Nov 22, 2010 | 1998 Ford Taurus

1 Answer

Replacing turn signla electronic flasher for 1999

Get the proper flasher from the parts store and start searching under the dash for the one that clicks when the turn signals are operating.

Aug 03, 2010 | 1992 Isuzu Rodeo

1 Answer

I think the electronic flasher needs replaced but

Im assuming that you are talking about the FLASHERS for turning and hazard lights, the Flasher is located front seating area, driver side, under dash, above kick panel, mounted in bottom of convenience panel.

I suggtes check the Service Manual ZJ-Secc-8W-Wiring-Diagrams (page 8). Also, you have a nice SUV, me too have an 1993 Jeep Grand Cherokee 5.2L MFI 8cyl.

Hope help with this (remember rated this).

Jul 16, 2010 | 1993 Jeep Grand Cherokee

2 Answers

How do i put my eectronic flsher in my car

I would suggest that the flasher is either in the fuse box, or in the electronic distribition box (black box near the front driver's side) in the engine compartment under the hood. Unplug old one and install new one with comparable replacement.

Apr 01, 2010 | 1999 Ford Taurus

1 Answer

How to replace the Electronic Flasher. Also the

Flasher is located in stearing wheel section of the car. Bushing in window motor worn.

Jun 29, 2009 | 1999 Pontiac Firebird

1 Answer

Electronic flasher

driver side, Under dash, under cover (knee protector) in the fuse panel, simply pull it out, pay attention where it came from & put new in same spot.

Apr 18, 2009 | 2001 Dodge Intrepid

1 Answer

How do I get a flasher relay to operate with LED lights

flasher relay is not a relay, it was a bimetal strip that heats on current flow, bends, breaks the circuit, cools straightens.
For LED lamps that do not draw enbough current to heat a bimetal, replace the old flasher can with an electronic flasher circuit,
This url shows both the old thermal type and new electronic type and is a place where it can be bought

Sep 21, 2008 | Honda S2000 Cars & Trucks

Not finding what you are looking for?
1999 Oldsmobile Aurora Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8832 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides