Question about 2006 Dodge Stratus

1 Answer

Replace haeadlaps cannot remove headlights to replace H/L bulbs

Posted by on

  • kronicaholic Jan 06, 2009

    brights still function but one low beam burnt out. need to know how to pull out the light assembly to unplug the bulb and replace. are there screws to take out or is there a certain direction to push down or unscrew the assembly from the back(under the hood)? i know that is what chiltons are for but i don't intend to do much work on my car by myself, i can't afford a book/heated garage to tinker in right now, much less a mechanic. the halogen lamp was bad enough. so that is what the internet is for. please help. i already looked through the 2006 JR41 Stratus Sedan pdf style with no luck.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

There should be just caps on the inside of the head light just turn them counter clockwise or they are rubbery and they just pop off then you can get tot the light/thanks for using fix ya please rate my response thank you very much

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACE HEADLIGHT 2008 SPRINTER


On some cases there are few hidden clips holding the assembly from under hood,that has to be released to remove headlight .

There are few troubleshooting help links showing how to replace car headlights,i suggest you to refer the links to solve these issue.

--------
Click the link below:------
How to Replace a Headlight http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb


http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html


How to Replace a Park Light Assembly http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------
Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------
Headlight Assembly Removal On Honda Accord http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html --------------- Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html-----------
How to Replace a Headlight Door http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

---------
All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------
How to replace HID headlight bulbs for lexus 400h? http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------
Working of Headlight switch?
------------
Both headlight bulbs blow together?
------------
Car headlight bulbs don't last long?



----------------
These will help.
Thanks.

Nov 23, 2012 | 2010 Mercedes-Benz Sprinter

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

How do you replace the headlight on a 2002 Daewoo Lanos


Hi there, together with providing you the solution to the problem, I also took the liberty of going one step further in giving you steps on how to remove the headlight bulb.

  • Find the hood release handle and activate it, the hood should pop open.
  • Once the hood is popped open locate the hood secondary or safety latch and release it. Then finish opening the hood.
  • Locate and remove mounting clips for any plastic shields that cover the headlight lens mounting screws or clips.
  • Some headlight bulbs can be replaced by simply grasping the bulb socket behind the headlight lens and turn it counter clockwise to remove it. This will expose the headlight bulb.
  • If the headlight bulb socket is not accessible the headlight lens may need to be remove or obstructions behind the bulb removed to gain access to the headlight bulb socket.
  • To remove the headlight lens remove all mounting screws and clips that hold the headlight lens in place.
  • After the headlight housing has been removed from it's mounts, release the headlight bulb from the headlight lens housing (turn counter clockwise) the bulb will then come out of the headlight assembly. Once removed, visually verify that the replacement bulb is exactly the same as the failed bulb before to ensure a proper repair.
  • Clean the headlight lens free from all debris to help maintain the seal from the bulb to the lens. This will keep moisture out of the lens.
  • Install the new headlight bulb by turning the retainer ring or bulb clockwise.
  • Re-install the headlight lens housing and reinstall electrical connector.
  • Re-install plastic covers.
After the job is complete turn the ignition key to the "on" position and activate the headlight switch. Observe the newly replaced headlight bulb to ensure proper operation.

Glad to be of help!!!

Jan 21, 2011 | 2002 Daewoo Lanos

1 Answer

How do I remove halogen low beam head light to replace it?


Removal & Installation To Remove:
WARNING
The halogen fog light bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
NOTE: The headlight bulb should not be removed from the headlight assembly until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlight bulb performance. Contaminants may enter the headlight assembly where they can settle on the lens and reflector. Never turn on the headlights with the bulb removed.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: Make sure that the headlight switch and the ignition switch are in the OFF position.
  2. Remove the pin-type retainers, screws and the air deflector from the radiator.
  3. Remove the three bolts and the headlight assembly.
  4. Disconnect the electrical connector.
  5. Remove the cover from the rear of the headlight assembly.
  6. If equipped with HID, release the spring tabs to remove the low beam bulb, otherwise disconnect the electrical connector and remove the bulb.
  7. Disconnect the electrical connector and remove the high beam bulb.
HID low beam headlight bulb lin_tc_0085.gif

Standard low beam headlight bulb lin_tc_0086.gif

High beam headlight bulb lin_tc_0087.gif

To Install:
  1. Place the headlight assembly in the proper position.
  2. Install the cover from the rear of the headlight assembly.
  3. Connect the electrical connector.
  4. Install the three bolts and the headlight assembly.
  5. Install the radiator air deflector.
prev.gif next.gif

Dec 18, 2010 | 2003 Lincoln Town Car

1 Answer

Need to replace headlight lens on a 1996 dodge avenger


Usually, one has to get the entire headlight assembly to replace the lens.
Is it cracked?
If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

---
REMOVAL & INSTALLATION

CAUTION
Halogen bulbs contain gas which is under
pressure. Handling the bulbs incorrectly could cause it to shatter into flying
glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
before removal. Handle the bulb only by the base; avoid touching the glass
itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

  • Turn the headlight switch OFF and allow the bulb to cool before
    changing it. Leave the switch OFF until the change is complete.
  • ALWAYS wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • DO NOT drop or scratch the bulb.
  • Keep dirt and moisture away from the bulb.
  • Place the used bulb in the new bulb's package and dispose of it properly.


Cirrus, Stratus, Sebring Convertible and Breeze


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the 2 screws securing the headlight module to the radiator closure
    panel.
  4. Pull out the headlight module from the vehicle.





    Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
    module retaining screws
    90906p69.jpg






    Fig. 2: Pull the headlight module straight out of the front of
    the vehicle to remove the bulbs
    90906p70.jpg






    Fig. 3: Disconnect the wiring harness for the headlight bulb
    90906p74.jpg






    Fig. 4: Turn the light bulb retaining ring counterclockwise,
    and remove it from the back of the module
    90906p75.jpg






    Fig. 5: Pull the light bulb out from behind the module. Never
    touch the glass of the light bulb
    90906p76.jpg



  5. Detach the headlight electrical connector.
  6. Remove the retaining ring holding the bulb to the back of the headlight
    module.
  7. Pull the bulb from the back of the headlight module. Hold the bulb by its
    base only; try not to touch the glass itself.
    To install:

  8. Holding the bulb by the base, place it in the headlight module, then secure
    with the retaining ring.
  9. Attach the electrical connector to the bulb.
  10. Install the headlight module into the vehicle and tighten the 2 retaining
    screws.
  11. Connect the negative battery cable and check the headlight operation.


Sebring Coupe and Avenger


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the sealing cover by rotating it counterclockwise.
  4. Remove the bulb attaching spring and pull out the light bulb.





    Fig. 6: Remove the headlight sealing cover(s)
    90906g28.gif






    Fig. 7: Remove the attaching spring and pull out the bulb
    90906g29.gif

    To install:

  5. Install the bulb into the headlight module.
  6. Install the bulb attaching spring.
  7. Install the sealing cover.
  8. Connect the negative battery cable and check the headlight operation.


prev.gif next.gif

Oct 07, 2010 | 1996 Dodge Avenger

1 Answer

Replacing my headlight bulb in my kia amanit 2004


  1. Open the hood of your KIA Amanti and look behind the headlight that has gone out. Locate the round knob on the back of the headlight.
  2. Turn the knob counterclockwise 1/4 of a turn and gently remove it from the back of the headlight. Carefully remove the electrical cable within the headlight housing that is attached to the back of the headlight bulb.
  3. Locate the metal clip that holds the light bulb in place by pushing the clip arm straight in and sliding it down. Remove the bulb from the headlight housing.
  4. Replace the old headlight bulb with new bulb. Secure it by sliding the metal clip up to hold the bulb in place. Reattach the electrical cable and replace the round knob to the back of the headlight housing.
  5. Turn on the headlights to verify that they are in working order.

Nov 03, 2009 | 2004 Kia Amanti

2 Answers

Changing the headlight bulb in 2003 dodge grand caravan


1) open the hood.
2) Carefully remove the three screws holding the headlight assembly in place.
3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. (Do not touchglass with your fingers or it will cause the bulbs to catastrophically fail - clean with alcohol pad if you touch the glass)
4) Carefully insert the headlight assembly back into place.
5) Replace the three screws removed in step 2 being careful not to over tighten.

Oct 30, 2009 | 2003 Dodge Grand Caravan AWD

2 Answers

How do i replace/remove the headlights from a 97 accord?


  1. Locate the headlight bulb that needs to be replaced. NOTE: It may be necessary to remove a component or the composite headlight assembly to gain access to the bulbs.
  2. Turn the headlights off.
  3. Detach the two prong connector from the base of the headlight bulb.
  4. Twist the bulb counterclockwise to unlock it from the headlight housing, then carefully withdraw the bulb from the housing. WARNING
    Do not touch the glass part of the bulb with your fingers. The pads of your fingers contain oils that will cause premature bulb failure. To install:
  5. Install a new bulb into the headlight housing, then turn it 1⁄4 turn to lock it into place.
  6. Attach the 2 prong connector to the bottom of the bulb.
  7. Turn the headlight switch on to make sure the bulb works, then turn the switch off.
  8. Install any components that were removed to get to the headlight bulb.

Mar 29, 2009 | 1997 Honda Accord

2 Answers

Headlight repair on 2003 Mercedes Benz E320


how do you change left low beam bulb on 2003 mercedes e320

Mar 15, 2009 | 2003 Mercedes-Benz E-Class

Not finding what you are looking for?
2006 Dodge Stratus Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...