Question about 1994 Acura Integra

1 Answer

Clutch pedal stuck to the floor

My clutch pedal is staying on the floor when i push it in how do i fix this.

Posted by on

  • Anonymous Oct 18, 2008

    where do i check the level for my chutch fluid?, It was getting softer for 2 or 3 days then one morning no more presher .. Im hoping fluid ,but cant find how to check. or if somone would know what elce it might be..

  • Anonymous Mar 16, 2014

    clutch pedal stuck on the floor

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Hi, there is one place you should check. but answer this first, did you swap the car with a new engine or did you pull the engine out of the car? if the anwser is "yes" then you'll probably twist a fluid tube for the clutch at the tranny. so check the front end of the tranny, it should be a short metal wire (tube like) that should be connection to the tranny. the bolt size is 8mm. so find that tube and open the line. then ask someone to pump the clutch pedal 3 or 4 time and stop while holding it down. yes! the clutch fluid should be coming out while he's doing that. so now when he's press down the last pump, you should twist it back on. repeat it, over and over until you get it to harden again. you should also open the clutch master cylinter, too and refill some more... well hope this help...

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

2 Answers

Clutch pedal stayed down when shifting


It is the clutch cable that get stuck, less often clutch disk. Register the clutch cable

Jul 27, 2008 | 1997 Toyota 4Runner

1 Answer

Why does the clutch petal stay stuck to the floor in my 94 honda accord?


They will usually have a bad slave cylinder or clutch master cylinder. See if you see any leaks at those parts. The clutch master cylinder may leak on the back side so you may have to look underneath the dash to see it. Fill with fluid and pump pedal, have someone look while pushing on pedal. It will be wet from the leaking fluid.

May 28, 2015 | 1994 Honda Accord

1 Answer

Can't get clutch to bleed on 1996 s 10 we have bleed bleed and bleed


Hi if you have done the following to bleed the clutch.
1 open bleed screw
2 push pedal to floor and keep on floor
3 do bleed screw up
4 lift pedal
5 undo bleed screw
6 push pedal to floor
7 do bleed screw up
8 lift pedal up
you need to repeat this a few times but making sure the fluid level dont drop below the lowest level else you will get air in the system.

right now if you have done the above properly and you still either get the pedal going to the floor and staying their or you have no pedal at all then this points to their being a fault with either the clutch master cylinder or clutch slave cylinder, now in most cases the one that fails is the master cylinder this is the one that is connected to the clutch pedal now its usually this one that fails and causes the pedal to go to the floor or have no clutch.

but it could also be the slave so bare this in mind, if the pedal comes back up after pushing it down then the chances are its the slave at fault and this is the one on the gearbox that operates the clutch arm.

let me know how you get on or if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Dec 01, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Clutch pedal stuck up


You have to replace the Slave Cyl. when you put on the new one you have to bleed it ..To get the air out of the new line.

Mar 10, 2010 | Hyundai Motor 2002 Elantra

2 Answers

Clutch pedal went to the floor but did not come back up. Heard something 'pop' when pushing in clutch last night. Got home, then tried to start car this morning and clutch made a 'pop' sound again when...


there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Oct 16, 2009 | 2003 Oldsmobile Alero

2 Answers

Clutch pedal stays to the floor and car is now stuck in neutral. Can raise the pedal with hand but will not raise on it's own


clutch hydralics is gone, meaning you have a leak, check clutch master cylinder, see if its empty, if so refill and pump pedal sevarel time may have to lift by hand sometimes then look for a leak,most times it the slave cylinder,thats what pushs clutch fork to disengage clutch. hope this is helpful good luck.

Oct 15, 2009 | 2003 Pontiac Sunfire

1 Answer

Clutch pedal stays on floor when released


check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Feb 21, 2009 | 1985 Toyota Celica Supra

2 Answers

1987 944 clutch pedal stays on the floor


look, if the clutch pedal is to the floor, there are about 3 different things that could be wrong. First check brake fluid to make sure full, see if there is any leakage under steering wheel and below transmission. Next could be the slave cylinder, it could be faulty or not bled right. Last it could be the master cylinder. If when you bleed the slave cylinder and have no movement in the arm inside the transmission then most likely the master cylinder is broken. Look under the steering wheel and see if everything looks entact. Watch the movement of the pedal and see if movement looks normal and see if fully attached. Good luck. Check www.clarks-garage.com for any problem in which you want to fix yourself. Great free site.

Jan 10, 2009 | 1987 Porsche 944

Not finding what you are looking for?
1994 Acura Integra Logo

Related Topics:

556 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...