Question about 2004 Ford Focus

1 Answer

Will not start

It will not start i have no feed to injectors, cam sensor replaced crank sensor replaced coil and still no joy put my snap on mt2500 on & it tells me i have a problem on the injector out put side any suggestions ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Have you changed the fuel filter; checked the fuel pump?

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced bad coil van cranks but wont start?


Sure the new coil is working? Did you check for spark?Is the fuel pump working? Fuel injectors? ECM?

Feb 21, 2016 | 2005 Chrysler Town & Country

1 Answer

Wont start. it has injector pulse but no spark


is there power and ground to the coils?

If there is injector pulse than the crank sensor has to be good. Injector pulse and spark are both calculated off from the signal from the crank sensor.

Checking for power and ground to the coils is a good place to start. If that checks out than either there is a wiring issue in between the PCM and the coils or possible the PCM has failed.

Nov 20, 2015 | 2001 Pontiac Firebird Trans Am

1 Answer

Car stalled at30mph and wont start back up


  • Cranks but no start condition-do below to determine whether it's fuel or spark issue:
  • Get a helper disconnect a sparkplug wire or 2 and ground it to the engine at least 3/16 away from ground -have helper crank engine over-do you have a snapping blue spark? If so-you have a fuel related problem, check the fuel pressure to rule out the fuel filter/fuel pump/pressure regulator and listen to the injector/s are they pulsing or hook up a noid light. No snapping blue spark continue to troubleshoot the ignition system-power input to the coil/coil packs,coil's resistances,distributor pick-up coil, ignition control module, cam and crank sensors and computer Note: If it doesn't apply disregard it.
make sure it is getting enough gas pressure

Dec 05, 2010 | Geo Prizm Cars & Trucks

2 Answers

1997 dodge ram won't start. My fuel pump does not run and coil won't spark. Iv'e checked fuses and relays and they look fine. Could a bad fuel pump cause the asd to kill power to the coil?


First check any ignition/fuel related fuses. Check to make sure you have 12 volts coming into the pump and coil. If nothing to the fuel pump replace the fuel pump relay - if you do have power to the fuel pump then replace the pump. If nothing is coming to the coil it is either an ignition relay or a wiring issue. If you have 12 volts to the coil but no spark then replace the coil.
Also the fuel pump/relay would not kill the coil.

Jan 21, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Lack of spark and injector pulse on audi 80 have replaced coil pack distributor and crank sensor still no joy


lack of injector pulse? perhaps there is a controller problem..like a pcm or something....without anymore information, i can't tell you anything else.

Nov 19, 2009 | 1988 Audi 80

1 Answer

Car wont start


being 94' im sure it has high miles, cam and crank sensor common to fail over time do to wear and heat exposure. check the basic, make sure you getting fuel and sparks. fuel pump only work as long the engine is turning over due to the crank sensor sense the flywheel turning. crank sensor may be faulty. no sparks, check coil make sure is good and putting out 12v, auto zone can test it for free. good coil, than check cam sensor, cam sensor senses the cam turning and tell the ecu to tell the coil to disperse the sparks to the plugs. cam and crank sensors, there no way of testing it but replacing the unit unless you have the special equipment to test it; both is fairly cheap to replace, check ebay.

Oct 24, 2009 | 1994 Mazda MX-6

2 Answers

1996 Jeep Grand Cherokee No Start


I would be thinking that there is a good chance that you need to be checking out replacing the computer, if you aren't getting any communication with the proper scan tool then the computer isn't communicating with anything in the vehicle...... I would have guessed first off that the ignition control module might be bad but that is obviously part of the computer also, I would be looking in that direction.

Sep 19, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Car has no spark or injector pulse(new ecm,crank sensor)


Check the fuse for the injectors, some vehicles have the injectors and coil running on the same circut, at the same time check the fuse for the ignition.

Jan 30, 2009 | 1996 Dodge Avenger

2 Answers

I cant get spark out of the coil pack


cam sensor fires the injectors to synchronise injector pulsing with the spark at the spark plugs.. U need to probably change the crankshaft sensor (around the crank pulley) as the crank sensor is what controls the ignition spark.
hope that does it.
:)

Jan 20, 2009 | 1996 Plymouth Voyager

1 Answer

1995 DODGE RAM B1500 NO START


You need to use a LED type test light for the injectors or a Bosch style Noid light for the injector. To test the cam/crank sensor signal you either need a scanner to read them or a lab scope to show you a signal. The pickup plate in the dist handles the injector timing, the crank sensor provides a RPM signal. They both feed the computer information for ignition timing. Good fuel pressure, injector activity(Noid), and good spark out of the coil. The coil is what I replace the most of.

Nov 19, 2008 | 1995 Dodge Ram

Not finding what you are looking for?
2004 Ford Focus Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...