Question about 1996 Chrysler Town & Country

1 Answer

Starting problem no fuel pressure

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Check the fuel pump if it is running. if it is running and still low on fuel pressure, check the fuel filter. could be clogged.

tnx 4 using fixya,


drcool

Posted on Oct 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 ford expedition i have been have trouble starting it for a month now changed the fuel filter reset the fuel pump switch checked the fuses all good. It turns and half the time it starts now...


GO TO AUTO PARTS STORE BUY A FUEL PRESSURE GAUGE THAT CAN CHECK FUEL PRESSURE UP TO 100 PSI. LOCATE YOUR FUEL PRESSURE TEST PORT.LOOK FOR SCHRADER VALVE ON FUEL LINE NEXT TO EGR VALVE.PLACE A RAG NEAR THE SCHRADER VALVE AS YOU INSTALL FUEL PRESSURE GAUGE TO CATCH GAS SPILL AS YOU SCREW IN FUEL PRESSURE GAUGE HOSE FUEL PRESSURE 30 - 45 PSI WITH ENGINE RUNNING. THE ENGINE MUST BE OFF HOOK UP THE FUEL PRESSURE GAUGE.IF YOU HAVE TROUBLE THE FUEL PRESSURE GAUGE WILL HAVE INSTRUCTION HOW TO HOOK UP FUEL PRESURE GAUGE.BE CAREFUL CHECKING FUEL PRESSURE IS DANGEROUS JOB.DONT ALLOW NO MASSIVE FUEL SPRAYING WHEN HOOKING UP FUEL PRESSURE GAUGE YOU WILL GET CAR FIRE.

Jan 04, 2011 | 1999 Ford Expedition

1 Answer

Started ran for awhile then died an wont start


Start with the simple and replace your fuel filter, a dirty filter can cause your engine from starting. At worst, your fuel pump has failed and will need to be replaced. Before replacing the fuel pump, inspect all the fuses and wire leads from the fuel pump harness. Note: that the ground wire is separately grounded at the frame, so inspect that for any damage due to corrosion.

You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors. I think each injector is on a seperate driver on that one. Check for pulse to all of them.

You may be weak on fuel pressure, even a couple of lbs low on a cold start will cause a no start. Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems. One test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test, here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure. Later V6 and V8 gm engines should have 60-66 fuel pressure.
* Cold start should be 64-65 lbs of pressure. If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
* Engine running should be 60-66 lbs pressure depending on engine load.
* Full pressure with return pinched off should be 75-85 or more. and if it has a fast leak down after shut off you have a leak.

The 75-85 is only a check on the capable full pressure of fuel pump. If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.

Mar 18, 2010 | 1999 GMC Sierra

1 Answer

Will not start only backfires and start dieseling.5.7 automatic. hear fuel pump running. ran fine last trip and parked overnight. few times in past week or two. little trouble starting. rough idle for few...


You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors.
I think each injector is on a separate driver on that one.
Check for pulse to all of them.

You may be weak on fuel pressure . Even a couple of lbs low on a cold start will cause a no start. Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.one test is to give it a squirt of carb cleaner not starting fluid. If you get a intake or engine full of starting fluid it can blow things. Carb cleaner will start it if it is a fuel problem and lot safer. Also in the good old days when i was a kid, i used to get a couple of cans of starting fluid and get in the back and have a good starting fluid spraying contest. Good for a big blast if someone lights a match. If it starts then you have a fuel pressure problem. Run the full fuel pressure test and post back pressures.

Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel. Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.


The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have done.
What are your cold start pressure readings?



Feb 01, 2010 | 1998 Chevrolet C1500

1 Answer

Truck turning over but not catching


You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors.
I think each injector is on a separate driver on that one.
Check for pulse to all of them.

You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.

The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have done.
What are your cold start pressure readings?
Post back what you have.

The other thing to is when was the last time the fuel filter was replaced? The fuel filter may have got to the end of it's like and may need to be replaced, the fuel filer should be replaced every 15,000 miles or once a year to ensure the fuel system is running 100%.

Good luck and keep me posted, be glad to help you get your blazer running again soon.

Jan 10, 2010 | 1997 Chevrolet Blazer

2 Answers

1997 chevy blazer getting fuel and spark but not starting, only backfiring through carb.


You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors.
I think each injector is on a separate driver on that one.
Check for pulse to all of them.

You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel. Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.


The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have when done.
What are your cold start pressure readings?
Post back what you have. Good luck

Dec 24, 2009 | 1997 Chevrolet Blazer

1 Answer

99 Tahoe engine cranks, wont start


You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors.
I think each injector is on a separate driver on that one.
Check for pulse to all of them.

You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.


The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have done.
What are your cold start pressure readings?
Post back what you have.


The other thing to that is common is the (ICM) under the distributor cap. There is a breather screen on the bottom of the distributor that get's clogged with dirt causing condensation promoting corrosion, this was gm TSB for replacing the cap and rotor to make sure it's clean.

Good luck and hope this helps. Merry Xmas.

Dec 24, 2009 | 1998 GMC Safari

1 Answer

Car wont start. Has spark, tried Carb Cleaner.


You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.

The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have done.
What are your cold start pressure readings?
Post back what you have. Good Luck

Dec 24, 2009 | 2002 Chevrolet Blazer

2 Answers

On cold mornings, will not start and just "turn over" replace fuel pump and complete tune up ..still the same problem


You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.
Post back fuel pressure readings.

The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.

What are the pressure readings that you have done. Good luck and hope the fuel pump is not a bad one you put in there, it's know to happen.

Dec 23, 2009 | 2002 Chevrolet Blazer

1 Answer

I have a Silverado 1500, 4.3 with 132,000 miles. After start, it runs fine, no signs of malfuntion. However it takes extended cranking to start. The fuel pump & filter was replaced 10,000 miles ago....


You need 3 things.
Compression
Good hot blue spark to all plugs.
Good gasoline and proper fuel pressure. 63-64 lbs.
If you have all 3 then move on to injector pulse to all injectors.

You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start. Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems. One test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem. Run the full fuel pressure test and post back pressures. Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.

Also you mentioned that you replaced the fuel pump, it's common for the $15.00 wire harness from the fuel pump to the frame will break and there is a bad connection till the wires heat up. You can try this trick, turn your ignition on for 30 seconds "engine not running" and then turn it off for for 5 seconds and then try to start. This will energize the fuel line if the fuel line check valve is bad which is a part of the fuel pump and will heat up the wire harness which will make a better connection and see if the engine starts easier. Regardless, inspect the wire harness for corrosion and the ground is good. Good luck and keep me posted.

Dec 15, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
1996 Chrysler Town & Country Logo

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...