Question about 1992 Chevrolet C1500

1 Answer

1992 2500 4x4

After sitting for the summer, my 1992 chevy 4x4 does not go into 4 wheel drive when I put the selector in 4 hi or 4 low. It woked fine the previous winter.

Posted by on

  • Anonymous Oct 23, 2008

    I just had the same problem tonight after pheasant hunting I needed the four wheel drive to get out the mud.The truck would not lock into low or high

    I was lead to belive by a Friend of mine that the switch is bad.Apperently there is a switch on the front axle that is a common problem but I am not really sure that is why I am looking here Good luck

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bad actuator

Posted on Oct 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 land rover discovery 2 sd model will not engage into 4 wheel drive and the engaging handle has no pressure at all?


Your DII is (always) in 4 wheel drive. There is NO 2x wheel drive option on a DII, it's always in 4x4 high, or low. To select 4-wheel drive low, put your transmission in neutral and pull down the high low gear selector.

Jul 12, 2014 | 2000 Land Rover Discovery

1 Answer

4x4 low will not engage but 4x4 hi will in my 2001 2500 HD SILVERADO


try coasting at 10 mph, place transmission in neutral and try placing in 4 wheel low while rolling at 10 mph then if selector moves you can then put transmission back in drive .same way going back to hi 4

Mar 18, 2014 | 2001 Chevrolet Silverado 2500HD

1 Answer

Problems with chevy s10


have the actuator (mounted on the drivers side transfer case) checked. that is what makes the selection from 2-4 hi-4 low. it takes the place of a gear shift. they are a fairly inexpensive and easy repair (if thats the problem). i would start there providing you have checked the fuses and relays. i hope this helps.

Jan 31, 2014 | Cars & Trucks

1 Answer

My 2008 Kia Sorento is stuck in four wheel drive. How do I fix it? Thanks, Bill


I assume that the vehicle has a rotating knob on the left side of the dash for four wheel drive. It may have been put into 4 low by mistake. To get it out, start the vehicle and put it in drive, select 4 low on the 4 wheel drive selector, take your foot off the brake and get the vehicle rolling at a walking pace (1-2 m.p.h.) then move the selector to 4 high, stop the vehicle and move selector to 2 high.

Jan 16, 2011 | 2004 Kia Sorento

1 Answer

How to use the 4x4


well, if you are sitting still it is recommended you put vehicle in neutral and select 4x4 indicator to desired posistion..... 4 high...4 low...or 2high (auto) when you select 4 low the top speed is not to exceed 25 mph. It is a very low gear for crawling or pulling. At any time you need 4 low gear you must stop trk, shift to neutral and select 4 low. The same procedure is done to change from 4 low to 4 hi or 2 hi. if not done this way internal trans, transfer case or driveline failure will occure. At any time you may shift 4x4 selector from (auto) or 2 hi to 4 hi, and 4 hi to 2 hi or( auto).****** But note, do not make shifts while tires are spinning or under power (acceleration)******* While driving you can make shifts at any speed between 2 hi (auto) and 4 hi and back to 2 hi. release throttle a little and select. you do not have to take foot off throttle all the way! just enough that truck is not under a power, load acceleration. If tires are spinning or you are on the gas and you select gears from 2 & 4 high the posibilities of severe damage can result. Also note that 4x4 is not recommended on dry pavement. When 4x4 is being used also take care as to the handling and the steering characteristics change, On tight turns the front wheels will bind and possibly **** a little. If you have never had a 4x4 before, obey what i have told you untill you get the experiance and you will be fine. HAPPY TRAILS.... AND A LITTLE 4X4 FUN!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Jan 12, 2011 | 1998 GMC Jimmy

1 Answer

My kia soernto 4x4 light flishing


I assume that the vehicle has a rotating knob on the left side of the dash for four wheel drive. It may have been put into 4 low by mistake. To get it out, start the vehicle and put it in drive, select 4 low on the 4 wheel drive selector, take your foot off the brake and get the vehicle rolling at a walking pace (1-2 m.p.h.) then move the selector to 4 high, stop the vehicle and move selector to 2 high

Dec 12, 2010 | 2007 Kia Sorento 4x4

1 Answer

Will not go into 4 wheel low


Make sure you have it in (N) before shifting it. Did it work before?

Apr 10, 2010 | 2000 GMC Sierra

3 Answers

Wont swictch back into 2 wheel drive from 4 wheel hi


you could have a split vaccume line goin to the actuater switch that operats the 4 wheel drive under neath the battery box.

Dec 17, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1992 Chevrolet C1500 Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...