Question about 2005 Chrysler 300

1 Answer

Error lights battery went dead. after recharging the abs brake and engine lights will not go out. how do i reset them

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 70,346 Answers

Disconnect the bttery for 5 minutes this should reset the lights, only disconnect the negative post.

Posted on Oct 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset abs computer


have a auto check it out and run proper diagnostics 2 reset the codes via computer

Apr 29, 2014 | 2002 Toyota 4Runner

1 Answer

Steering wheel light is on after battery went dead (along with traction control).


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS, TPMS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Anti-lock brake system. TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module. TPMS Tire Pressure Monitor System

Nov 05, 2012 | 2009 Volkswagen Tiguan 2.0

1 Answer

Battery power to car went dead dsc and brake warning light and flat tire monitor lights stay on i recharged the battery now have power but lights are still on


You will have to get the computer reset. Auto Zone used to do it but now they wont. Some shops do it cheap. Or try Auto Zone and see if they will do it for free.

Mar 06, 2011 | BMW 330 Cars & Trucks

1 Answer

The alternator went out on my 2005 Ford F250 with 6.0 Diesel. The batteries went dead. After replacing the alternator and recharging the batteries the ABS light stays on and the speedometer doesn't work....


Depending on why the alternator went out you could of caused a surge into the ABS module causing it to fail. Very common. The speedo comes thru the module which to me indicated the module failed.

On monday call modulemaster.com and run this by them. The module can be rebuilt for a couple hundred bucks.

If your sure you didnt leave anything unplugged getting a diagnoses or calling this place is going to be your only options.

Apr 03, 2010 | 2005 Ford F 250 Super Duty

2 Answers

My Car shut off, I found out it was the


ABS is Advanced Brake Systems, but that light should flash once when the car is turned on to signal it works.
If you turn the key in the ignition forward, like you are going to turn it on, but not far enough to turn the engine over, that light should be on at a constant. with it turning itself off upon starting.
If you have a no start issue, it would have the same effect. But if it is a no start, it's not going to be a dead battery, the battery puts out enough charge to turn the engine over (on), and the alternator runs everything.
Alternators run off the belt(s) on the engine and need exact tension, in order to produce the proper amount of power.

Jan 05, 2010 | 1998 Chrysler Town & Country

1 Answer

The abs light came on and air conditioner started blowing hot. After work the batt was dead. Jumped it and guages were dead for about 30 sec. About 10 miles later abs light went off and air got cold again....


It sounds like the engine is running on battery power only.The engine of today`s technology needs the alternator to have enough ignition to run on,lights and computer,etc,will be affected by low voltage,and amps.The alternator is not charging,look for a charging fuse to see if it is blown.If the fuse is fine,replace the alternator,and have the battery recharged on a slow 2 amp charge so it will recover it`s loss of deep cycle amps.This will prolong battery life and alternator.If I can help let me know.Let me know the out come.

Aug 29, 2009 | 2004 Ford F350

1 Answer

Cannot read codes


Try disconnecting the battery again then hook it back up and see if it resets. We will go from there.

Dec 24, 2008 | 2001 Volkswagen Beetle

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...