Question about 1999 Daewoo Nubira

1 Answer

Gear oil We have change the clutch in our daewoo nubira 2.0 from1998. we cant see wher to put new oil in! can you help us?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

A lot of times frontwheel drive transaxle gearboxs have the filler hole located where the speedo drive goes into the gear box so you remove that n then tip your oil in... in the workshop manual it will say theres a certain position to fill it to on the speedo drive so in fact the speedo drive is your dipstick..from the info ive got in front of me the transmission takes 75w-90 gear oil n 1.8 litres fill capacity

Posted on Oct 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What. Is. The. Position of. No 1piston. When. Setting. The. Timing. On. Daewoo. Nubira. Cdx. 2 l


after you remove the timing belt covers on the crankshaft gear have a noch face down to alaing tho the oil pump cover on the camshafts have two marks a the top of timing cover

Sep 09, 2014 | 2002 Daewoo Nubira

1 Answer

Daewoo nubira clutch


I can only suggest that you have a rubber seal breaking down inside one of the cylinders possibly the master ,could be someone has topped the fluid up with the wrong fluid ,as for the squeak ?? could be the clutch arm as it has a pivot point type ball inside the bell housing and was it greased when fitting the new clutch ,tut tut i was taught to oil and grease everything if moved oil it and lo betide me if i missed a grease nipple .

Mar 09, 2014 | Cars & Trucks

1 Answer

Is my 2000 Daewoo Nubira oil pump going out?


That would be my first stop in this situation assuming you also changed the oil filter when you changed the oil.

Jul 26, 2010 | 2000 Daewoo Nubira

1 Answer

Clutch problem


Have someone press down on the clutch pedal while you look at the release lever. There should be movement on the lever of about a 1/2 inch. If not the problem is on the hydraulic side. If there is sufficient movement the problem is on the mechanical side (Incorrect fitment/ cracked release lever in the bellhousing/incorrect parts ie pressure plate) Pay attention to where the slave cylinder pin contacts the release lever. Severe wear can occur at this point as it is hardly ever lubricated by service centres/backyard mechanis and you could have a situation where the pin goes straight throught the contact point due to wear.
Bear in mind, (something that has puzzled me completely), a master cylinder that has been inoperative for a while, especially on older cars, needs to have its' seals replaced before working properly again. Go figure!

Jun 07, 2010 | 1999 Daewoo Nubira

2 Answers

2004 daewoo matiz se - Truoble getting in first gear.


It may be the synchro of the first gear.  It may have been worn out.  To check, you may try to put it in 2nd gear before putting it into first to be sure.

Jun 08, 2009 | 2002 Daewoo Nubira

4 Answers

What is trouble code P1887?


Torque converter clutch release circuit.

May 04, 2009 | 1999 Daewoo Nubira

1 Answer

Daewoo Nubira Starter Motor Refit.


changed a clutch on one of these a few weeks ago and cant remember what i done ,old timers i think ?? not sure but its from below with a rear support bracket ,and a inlet manifold stay bar ,,,3/8 drive socket set with a knuckle and 3 long extension bars to get to top inside bolt as well i think ?? honestly cant remember ,i work on all makes and cant remember every one

Apr 14, 2009 | 1999 Daewoo Nubira

1 Answer

Cd Player In a Daewoo Nubira 98


its easy rip off the covers and on the side you will see a set of gears, i cant remember what direction but spin them until the tray moves and the steel bars will drop down

Apr 06, 2009 | 1999 Daewoo Nubira

1 Answer

Trouble changing gears 1st and 2nd


If the clutch feels firm with no play u may have worn syncronizer's in the trans, take it to trans shop and have them road test it, they will not charge in most cases.

Jan 21, 2009 | 2002 Daewoo Nubira

1 Answer

Manual tranmission


your syncronizers are out

Aug 15, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

437 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...