Question about 1999 Lincoln Town Car

1 Answer

Tail lite How do I get to the license plate light bulb on a 1999 lincoln town car. there is plastice plugs that appear to be screws but do not unscrew only spin.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

If they are plastic they are plugs, on mine they are metal screws.

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of tool do you need to change out the license plate bulbs on 2001 Lincoln town car?


Gently lever off the plug on the liner, and twist them out.

It will be the same as this video.

Lincoln ls 2001 license plate bulb

Jan 26, 2016 | 2001 Lincoln Town Car

2 Answers

Tail lights work but why don't license plate lights?


The license plate lights have their own separate bulbs. If you are able to replace the bulbs, that may solve your problem. If not, you may have a loose or rusted connection to the plate bulbs only. If you are able to gain access, you may want to check the condition of the harness that supplies the power to the license plate portion. Good luck and have a great day.

Aug 30, 2015 | 2001 Toyota Tacoma

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

How do I get to the license plate bulb for a 2004 nissan sentra


There are 2 bulbs above the license plate, each under a plastic cover. The covers are held in with 2 screws each. Just unscrew and remove the plastic covers and you should be able to access the bulbs.

Mar 21, 2014 | 2004 Nissan Sentra

1 Answer

Tail light bulb


Some manufactures incorporate a recess part on the screw so that they screw all the way through then turn any which way but won't fall out. If you have to remove the screws apply pressure to the point while unscrewing and the thread should pick up and wind out.

Aug 13, 2013 | 2003 Ford E150

1 Answer

Tail lights inoperatrive


Could be one of three things;
1. Check the fuses in the fuse box.
2. If all fuses are OK, check the headlight switch.
3. If this car has 'delay turn off lights' feature, the lighting control module should be checked.

Nov 12, 2011 | 1993 Lincoln Town Car

1 Answer

Schematic_Diagram 93 lincoln town car tail lights and license plate light.


Sounds like either your wiring from the Light switch is bad or the Light switch itself is bad. Check with your Owners manual to see if the "Parking lights" have a separate fuse.

Your tail and License plate lights would light with either the Headlights or the "Parking" light selected at the switch as would the front parking lights. If all lights except the headlights are out, your problem is closer to the light switch than at the mounting points of each Parking light or License plate light.

This is one case where you will not know if a dead wire off of the switch is dead because of a bad switch or a bad wire. You would have to detach the harness at the switch, test the wire bundle or jump the switch with power to see how it distributes power through the Harness. It will take a lot of time to rule out the switch. It may be cheaper to replace the switch and then work from there.

Nov 07, 2011 | 1993 Lincoln Town Car

1 Answer

How do you replace the license plate light bulbs on a 2002 Cadillac STS?


Hi there,

There are two bulb containers above the license plate light and you just need a small screw driver to press in under the left side of the plastic bulb housing to release the plastic clip. The plastic bulb holder will swing from the right hand side and will then fall out. All you need is a medium size flat head screw driver.

You have to unscrew the housings with a philips screw driver and take the housing out of the hole, by turning it sideways and pulling it out. Then turn out the bulb holder from the back of the housing and pull out the bulb.

Hope this helps...

Jan 24, 2011 | 2001 Chevrolet Blazer

1 Answer

The lights around my license plate are out. I replaced them and they are still not working. I am wondering about the fuse, but am not sure which fuse controls these lights on a 2000 Lincoln Town car


not sure which fuse except to say same fuse as tail lights is one you're looking for. try turning your park lights on and wiggling bulbs back and forth,i suspect a bad ground inside bulb holder. you can wiggle bulb to check that. after you do get it working i suggest you apply some bulb grease to put into bulb socket for no future problems.

Aug 19, 2010 | 2000 Lincoln Town Car

1 Answer

2006 lincoln towncar Burnt out light bulb


I recommend autozone if you buy the bulb from them they will assist you but I believe it has to be replaced from inside the trunk

Jan 12, 2009 | 1999 Lincoln Town Car

Not finding what you are looking for?
1999 Lincoln Town Car Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...