Question about 1994 Ford F150 Styleside Supercab

1 Answer

It dies when put in gear

When your setting at an idle and you put the truck in reverse,first,or second gear it kills the motor instantly but will hold its self against the brake in overdrive. When the motor is cold everything works fine when it reaches running temp then the check engine light come on and starts acting crazy.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 160 Answers

Have someone check it with a code reader to determine reason for the check engine light. it could be the source of your problems. the check engine light comes on so you know there is a problem. with most vehicles becoming more complex, the code reader can be used to pinpoint many problems that are not detected otherwise.

Posted on Nov 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reverse it took a few seconds to engage into gear to move when it moved I put it in drive and went forward then a small thumb occur and the motor stopped what


Does it kill the motor when you try to put it in gear now(fwd or rev)? Sounds like the torque converter clutch. Transmission part. Usually at about 150,000 miles. Hope that helps.

Feb 26, 2016 | 2006 Jeep Grand Cherokee

1 Answer

Why does my truck die when I put it in drive


Stalls when put into Drive or Reverse - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1987 - 1996 F150 & Larger F-Series Trucks
May 22, 2012 - Stalls when put into Drive or Reverse 1987 - 1996 F150 & Larger ... the fluid that was needed...my truck would stall when I shifted into reverse. 1995 Bronco stalls when put into drive
Jun 13, 2013
ford powerstroke truck dies in reverse
Oct 29, 2011
Truck dies when putting in gear and giving it gas.
Feb 26, 2011
ENGINE IDLES FINE,DIES WHEN PUT IN DRIVE
Jun 26, 2010
More results from www.ford-trucks.com

TRUCK DIES WHEN PUT IN REVERS


Nov 30, 2015 | Cars & Trucks

1 Answer

1990 thunderbird cranks up fine but when shift into drive or reverse car shuts off like turning switch off no jerking or anything engine just stops immediately


What happens if you give it a little gas ? Hold the RPM's up , will it keep running then ? How does it Idle , smooth or ruff ? Does the idle seam low ?

Mar 23, 2015 | 1990 Ford Thunderbird

1 Answer

Timing chain


you have probably knocked somewires loose like cam sensor or crank sensor re check all your wiring near where you did all the work..

Apr 03, 2014 | 1994 Chevrolet Camaro

1 Answer

Need help on a 1995 Chevy Suburban. It will die at idle when it's up to running temp and in gear. I have to pump the gas peddle to keep it from dying. Just did a tune up and throttle body cleaning to see...


it sounds like the motor's tick over is far to slow when the car is put in gear if the tick over is say 750 rpm out of gear then it stalls when you put it in gear lift the tick over up to say 850 rpm the best way to set this up is have a friend sit in the car, warm the motor up, then get your friend to hold the foot brake hard on and put the car in gear, if it stalls bring the tick over up (in gear) till it dont stall,,,but hold the brakes hard on when your doing this,,,getting run over is not a nice thing to hapen to you and it wont make your day? you should feel a dit of a thump when you plop it into gear so hold the foot brake down when you do plop it in gear every time you do so, it saves the transmishion getting a thumping, all the things you have done to your car so far have only done it good, but why not change the oil and filter as well and know you have done the full monty on your car, and it wont need another service for another year or so?????

Jan 05, 2010 | 1995 Chevrolet Suburban

1 Answer

Motor dies instantly when put into gear.


i am arko iam looking for a softare for haking for mobile phone line & and memory

Dec 06, 2009 | 1996 Dodge Caravan

1 Answer

1991 ford probe


duck tape on the air intake. I just fixed mine. There is a crack on the intake that lets too much air in when you put it in drive that makes the car stall. Try it it works.

Nov 23, 2008 | 1990 Ford Probe

1 Answer

91 camry starts and shuts off when put in drive or reverse


I was an ASE master auto tech for 13yrs and have seen this problem before. It sounds like the idle air control valve on the intake manifold has stopped working and the idle speed is not being controlled(letting the engine idle too slow which causes a stall when put under a load such as putting it in gear). Try giving it a little throttle while putting it in gear if that works let off the throttle if it dies you will know the Idle Air controll is not working.

Oct 12, 2008 | 1991 Toyota Camry

Not finding what you are looking for?
1994 Ford F150 Styleside Supercab Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...