Question about 1995 Acura Legend

1 Answer

Need to know where on board computer is located to reset codes

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 63 Answers

In the glove box either above or below it.

Posted on Oct 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you reset the computer on a 2000 Mitsubishi galant 2.4 l es and does anybody know where the MAF sensors regulator is located


Explain what you mean by reset

When you clear codes, you clear all
data, needed to work on the vehicle
& find problems

There is nothing that gets reset that fixes
any issues, on any vehicles

The MAF Sensor is in the same place on all vehicles

Between the air filter & the intake manifold

You can use the internet to see pictures of just
about any item

May 01, 2014 | Cars & Trucks

1 Answer

I have messages that keep popping up on my dash board. I want to know how to reset the computer.


have you tried disconnecting the battery for about ten minutes? that usually will reset the cars computer. or plug in an OBDII scanner and reset each code.

Apr 16, 2013 | Cars & Trucks

2 Answers

Location computer reset button 1999 windstar


I don't know of a reset button. it's been my practice to unhook the battery for several minutes to reset the computer on all of my car's

Jul 16, 2012 | 1999 Ford Windstar

3 Answers

How do you turn off engine light in a 2003 chevy suburban ?


This will require a code reader/scanner. They are from $30-$300.. You just need the cheap one. Just make sure it erases codes, and most do. it is referred to as OBD2 ( On Board Diagnostics).

Jan 21, 2010 | 2003 Chevrolet Suburban 2500

2 Answers

I have a 2001 Chrysler Sebring LXI Coupe 3.0 mitsu engine, front O2 sensor replaced due to code on computer said to replace, code won't reset. Autozone says O2 sensor has a fuse but they don't know...


A great tool to have that can save you some money to read computer error codes and clear them after work has been done can be had for under $100 from Actron. This is what I have been using and its a life saver but it's also good to have the vehicles repair manual as well.

The computer on this car is OBDII like many other vehicles out there these days so you'll need a tool that can plug in and read the outlet located above the shin of your right leg under the dashboard or steering wheel. Here is a link to a bunch of their products on amazon Actron and other OBDII Computer diagnostic code reader tools.

Dec 26, 2009 | 2001 Chrysler Sebring

1 Answer

Need to know the exact location of the reset engine light


It depends if you have obd1 or obd2 computer, if you have obd1 jsut remove to battery cable for 5 minutes and it will reset the battery, if its obd2, you will need a code reader/programmer to do it. i am thinking being a 95 it may be a obd1, remove the cable for 5 minutes, go longer if you have the time, and reconect. let me know how it works. good luck.

Jun 21, 2009 | 1995 Geo Tracker

2 Answers

Compressor is off and will not come on, how do you turn the compressor on


It has freon in it? If yes, you need to reset the low freon shut down. To do this just unhook the battery for a couple of minutes.

May 31, 2009 | 1997 Cadillac DeVille

1 Answer

Location of on board computer


Under the seat on the passenger side. You'll need a manual to find how to get into the proper mode and then interpret the codes, which are series of flashing lights.

Apr 20, 2009 | Nissan Pickup Cars & Trucks

1 Answer

2001 Ford F150, need to know On Board Diagnostic reset timeframe


Take it to auto zone and have them scan the computer to see if there's codes. If you want to reset it by driving it might take up to 100 miles and you'll have to drive it in the city and freeway until the computer relearns all of its settings. I would just take to auto zone and have them reset it, its faster.

Mar 24, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Keyless entry code


They normally stamp the Keyless entry code in the trunk and if not I belive the Computer that controls this is located behind the Glove box and they normally have the code printed on it.

Jan 11, 2009 | 1987 Lincoln Mark VII

Not finding what you are looking for?
1995 Acura Legend Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...