Question about 2005 Kia Amanti

1 Answer

Rear brake rotor removal

Would like to know how to remove the rear brake rotor off a 2005 Kia Amanti. I have caliper and pads removed.

Posted by on

  • 2 more comments 
  • Anonymous Mar 15, 2014

    I do not know how the grill releases at the top

  • Anonymous Mar 23, 2014

    what bolts do i need to remove

  • Anonymous Mar 24, 2014

    2005

  • Anonymous Mar 28, 2014

    my brake light came on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Should just pop right off. Hit it gently with rubber mallet, it might have rusted to the hub

Posted on Dec 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2005 dodge ram 1500 how i can remove the rear brake rotor


first remove the two bolts that hold brake caliper on, hang caliper remove brake pads. On caliper holder remove bolts and remove wave washer on studs then remove rotor with hamer

Aug 16, 2014 | Cars & Trucks

2 Answers

Rear pad removal?


Here ya go! This is for the rear brake pads removal:

Removal & Installation
  1. Remove the brake master cylinder filler cap. Check brake fluid level in brake master cylinder reservoir. Remove fluid until brake master cylinder reservoir is half full.
  2. Raise and support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Inspect the brake pads for wear or contamination. If worn, damaged or past specification, install new components.
  5. Remove the caliper pin bolts.
  6. Remove the rear disc brake caliper.
  7. Remove the brake pads and rail clips.
  8. Inspect the disc brake caliper for leaks. If leaks are found, disassembly is required.
  9. Installation is the reverse of removal. Observe the following torques:
    • Caliper bolts: 27 ft. lbs. (36 Nm)
  10. // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 12, 2011 | 2002 Ford E350

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Procedure for changing front and rear brake pads on a 2004 Amanti



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Front wheel Caliper mounting bolt Suspend the caliper from a wire Pads from the caliper support Pad retainers, if necessary

To install:
  1. Install or connect the following:

    Pad retainers, if removed Pads onto the pad retainers
  2. Compress the caliper piston using a C-clamp. Rotate the caliper downward and install the mounting bolt. Tighten to 16-24 ft. lbs. (22-32 Nm).
  3. Install the wheel.



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Rear wheel Caliper mounting bolt Suspend the caliper from a wire Pads from the caliper support Pad retainers, if necessary

To install:
  1. Install or connect the following:

    Pad retainers, if removed Pads onto the pad retainers
  2. Compress the caliper piston using a C-clamp. Rotate the caliper downward and install the mounting bolt. Tighten to 16-24 ft. lbs. (22-32 Nm).
  3. Install the wheel.

Dec 16, 2010 | 2004 Kia Amanti

1 Answer

I can't remove the rotors from my 2005 kia sorento. I removed brake stuff. There are 2 phillups head screws on rotor but can't get them out. do they need to be removed? If so how.


Changing the brake pads can be done without removing the calipers. However to take off the rotor, the calipers needs to be out. The 2 Phillips screws are to hold it in the place, but to access the rotor, it has to be through the calipers. Good luck.

Sep 20, 2010 | 2005 Kia Sorento

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

3 Answers

How do i change the brake pads on a 2005 grand prix pontiac


remove the caliper, by removing the two holding bolts, then use a old brake pad against the pistons and a c clamp and push piston all the way in, next is to clean and lube pad mounting surface and the caliper slide pin, then install new pads on bracket then caliper and tighten caliper bolts, heres a diagram to help you,98c6b31.jpg150490f.jpg

Apr 16, 2010 | 2005 Pontiac Grand Prix

2 Answers

Will be replacing brakes on 04 kia amanti soon.Any thing i should be aware of when changing them?


Yes be careful with the caliper pistons, make sure they do not fall out.
You must push them back into the cylinders in order to put new pads in.
Thats now out of the way, Just be sure to lube up the sliding pins on the calipers. if you are replacing rotors be careful of the brake lines when you remove the caliper and to hang the caliper with a wire hanger or caliper hanger if you have one to not stress the brake lines

Jul 20, 2009 | 2005 Kia Amanti

1 Answer

R&R rotors and calipers on 2005 Ford 500 to do brake job


use a large c-clamp to bottom out the caliper pistons remove the caliper bolts .slip out the pads and remove the caliper from the disk
hang the caliper from a coathanger wire to avoid damaging the brakeline after replacement of the pads;brake bleeding is not needed Rotors are held on to the axle like a wheel; with bolts

May 29, 2009 | 2006 Ford Five Hundred

Not finding what you are looking for?
2005 Kia Amanti Logo

Related Topics:

504 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...