Question about 2000 Ford Crown Victoria

1 Answer

Turn signal and brake light

My passenger side rear turnsignal, brake light, or hazard light wont work all others do? The driver side rear occasionally does the same. Bulbs are fine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Check the plug in the trunk lid mine did that and the plug was completely disconnected, yours may just be loose, or have a broken wire

Posted on Jul 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

Turn signal and brake lights not working properly how do i fix this


turn on your hazard flashers then off again some times dirt gets arround this switch and causes funny things like that to happen. good luck

Feb 06, 2013 | 1988 Chevrolet G20

1 Answer

My brake lights, turn signals and hazard lights aren't working.


There should also be another fuse panel on the interior located on the driver or passenger side foot panels or there about.

Sep 20, 2012 | 2002 GMC Safari

1 Answer

1999 jeep grand cherokee - rear driver turn signal and brake light don't work. flasher, back up and running light works. everything works when lens assembly is plugged into the passenger side. can...


Check this diagram (click over pic for zoom)...

zjlimited_1040.jpg

Check the postion F4 / 15 Amp ( Lt. Blue ) Flasher, hazard switch (see Junction Block diagram above for location of turn signal Flasher relay - Mopar p/n 4686094)

Repair tip: WJ flasher repair.

Hope helps.

Apr 16, 2011 | Jeep Grand Cherokee Cars & Trucks

2 Answers

My 97 chevy blazer, the brake lights dont work but the third brake light does and the turn signals or hazard lights dont work??


More likely it is the hazard/turnsignal/highbeam/cruise control switch module. It costs about $275 for the module. However there is a repair kit for the likely culprit...the hazard button. Try jiggling it around a little, see if that helps. Spray a little WD-40 into it so it can jostle back into it's correct position. You could try a junkyard unit or Ebay. It's not too hard to change. The hard part is doing it without removing the steering wheel. It can be done. I've done it. But hopefully you can locate the repair kit which costs about 15 dollars. Good luck.

Apr 27, 2010 | 1997 Chevrolet Blazer

1 Answer

Emergency Flashers totally out, Rear lights malfunctioning


Check the ground on the passenger side rear lights, it's likely bad. As for the hazards, sounds like a bad flasher or fuse.

Sep 03, 2009 | Ford Super Duty Cars & Trucks

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

1 Answer

1998 chevy blazer


Unplug the turnsignal switch. If it stops then replace the switch. This is a common problem. Alot of times it is the hazard button that melts and causes it because all the turn signal functions go though the hazard switch but you have to replace the whole switch to fix it. Let me know what you find or if I can help you further. Please rate.

Dec 27, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...