Question about 1988 Ford Crown Victoria

Open Question

Vinyl top removal

How do i remove a vinyl top from a 1988 crown victoria

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 126 Answers

SOURCE: removal of lower ball joint

yes it is safer to use a bal joint press . and it goes downward.

Posted on Apr 17, 2009

  • 11 Answers

SOURCE: fix this please

NO. Your Horn is the #16 Fuse and your cruise control is your #17. Unless Both of those fuses are broken. it would be your steering well and in that case follow the advice of oda. Could also be something "Lodged" in the steering well too, weird huh? i thought so. but ya, the horn and cruise control are two seperate fuses. for the Ford Crown Victoria models of these models.. (And also the Mercury Grand Marquis too)

Posted on Jul 13, 2009

  • 4345 Answers

SOURCE: 05 crown victoria police package rear axle removal

there are two main designs. One uses a bearing and flange at the backing plate area, release that and you can pull the axle and bearing.

the Other design is call a c lock axle. Inside the carrier, there are 4 spider gears. Two are splined to the alxes and two idle on an idler shaft. Remove this shaft, and then you can push the axle shaft inwards about an inch or so.

this will allow you to remove the c shaped retainer that is engauged with a groove at the inboard end of the axle.

So, now the bad news: often the c lock axle uses the axle shaft itself and the inside bearing race...which means if the bearing has failed, you need to replace the axle also.... Inspect carefully. Metal temper is the issue and once that is comprimised, you need to replace.


Posted on Sep 19, 2009

  • 87 Answers

SOURCE: Need diagram for removing a power antenna motor

it would be at the base if the antenna

Posted on Jul 22, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I remove door panel on 1988 crown victoria

Remove the two screws in the armrest hole then you need to get a special tool to place under the edge of the door panel to gently pry the panel away from the door sheet metal. You can use a flat tip screw driver if you are careful. Get the tool or flat tip screwdriver as close as possible to the retaining clip before you pry the retainer loose from the door.

Sep 27, 2011 | 1988 Ford Crown Victoria

1 Answer

Where is the top nut of the back shock located on a 1986 crown victoria?

It's located between the frame and the body, you have to remove a rear wheel to get to it. The shock top mount is not accesible from inside the vechicle.

Jun 10, 2010 | 1986 Ford Crown Victoria

1 Answer

Where and how do you change freeze plugs in an 1988 ford crown victoria

theyre located on the sides of the block, about the size of a silver dollar, pop the old ones out with a screw driver, install new with a soft rubber malet. drain eng. coolant first though as you will leak antifreeze once plugs are removed

Apr 05, 2010 | 1988 Ford Crown Victoria

2 Answers

My horn doesn't work for my 1988 Crown Victoria

check fuse and also check the wire going to the horn and check the inside of the horn too and check the ground

Jul 04, 2009 | 1988 Ford Crown Victoria

3 Answers

Fix this please

If your horn doesnt work either you have to remove the steering wheel and there is the connector for the horn/cruise control. If nothing broken there, check the clock spring too!

Apr 19, 2009 | 1988 Ford Crown Victoria

3 Answers

How do i disable the horn on my 1988 crown victoria

Remove the horn relay.

To find the horn relay:
"look under the hood on the left, front side of the car there's a somewhat triangle shaped box with fuses in it. It has 1 latch @ the top(left side of the box) & 2 latches @ the bottom(right side of the box). Open & pull off top. Under top will be names of the fuses & relays you will need to take it out and take it with you to the parts store so they can match it up with one they have they may have to order it call first. "

from: WikiAnswers

Feb 24, 2009 | 1988 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides