2003 hyundai accent dtc p0760

P0335 - Crankshaft position (CKP) sensor - circuit malfunction.
P0755 - Shift Solenoid "B".
P0760 - Shift Solenoid "C".
This is two different problems. Your safest option is to take it to a Good mechanic. The Crank sensor monitors engine speed and can be positioned deep behind other engine parts. The Solenoid issues could be inside the transmission as these control when the gears shift and you will need someone familiar with them to sort it.

your transmission control module is going out.

How To Fix Transmission A4CF2 Shift Problems / Check ...

? 18:46
https://www.youtube.com/watch?v=URUT3t8uUCw
Oct 27, 2014 - Uploaded by ProProjects
Thanks to ProProjects P0700 P0743 Torque Converter Clutch Circuit Electrical. ... P0765 - Shift Control Solenoid Valve D (Overdrive Solenoid) ... I have only two codes P0760 P0755 but my car is a mitsubishi galant 2.4 liters.

PDF]Technical Service Bulletin - RevBase

www.revbase.com/BBBMotor/Tsb//DownloadPdf?id=133873
Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750,.P0755, P0760, P0765 or P0770 set ... P0700 - TCM MIL request signal.

did you also find out that P0755 & 760 were shift solenoids B & C respectively? probably looking at replacing those. Chiltons are no help when it comes to trans work. Had a '99 LH car with a 3.2L also. Maybe look for a Service manual online, you know the ones for dealers.

The P0700 means Transmission Control System (MIL Request)
The P0760 means Shift Solenoid "C"
The P0871 means Transmission Fluid Pressure Sensor/Switch "C" Circuit Range/Performance.
_________________
spare transponder key

Hello, all your codes are related to transmission shift solenoid circuit condtion eg: Transmission > Automatic Transaxle > P0750 Low and Reverse Solenoid Valve Circuit - Open or Short(GND). Automatic Transaxle > P0755 Underdrive Solenoid Valve Circuit - Open or Short(GND). Automatic Transaxle > P0760 Second Solenoid Valve Circuit - Open or Short(GND). Automatic Transaxle > P0765 Overdrive Solenoid Valve Circuit - Open or Short(GND). Wether your vehicle is equipped with a 4 cylinder or v6 ,all the codes are for either engine models. Check your main wire harness that plugs into the top of the transmission and verify,that a good connection is present. if all looks ok and the vehicle still exibits the same symptoms. The problem may also be in the ECM/TCM control module itself. A Hyundai dealer would have the proper scan tool and tester to verify and perform actuation tests on the shift solendoids themselves to make sure they are working correctly. This does not mean that the transmission itself has failed. You basically have an open circuit somewhere that the solenoids are not getting a good ground. Hope this helps.

P0760 - shift solenoid (C)

Temp sensor in the transmission. You can replace it yourself in about an hour. Take the time to replace the filter and you'll need an additive for replacement fluid as the transmission uses 'SP3', which you can only get at the dealer.

00-30-001 2000 ACCENT DMTL DIAGNOSIS: DTC CODES P1401, P1402 AND P1403

p1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected