Question about 1996 Ford Contour

1 Answer

Timing need marks for timing marks for crank and cam

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Try to use magnifying glass to see them they are present! probably under condensation rust!

Posted on Dec 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi. i need timing marks for a 2002 toyota camry 2.2. An image with the mark would be great. Thank you


The camshaft timing mark is on the cam seal housing there is a hole in the cam sprocket use a mirror to see the mark it’s in the 12:00 position. The crank mark is on the oil pump housing and a triangle notch on the crank sprocket

Oct 26, 2017 | Toyota Cars & Trucks

2 Answers

I am changing the oil pump on a ford fiesta TdCI and I need to know the cam belt timing marks or a diagram on the cam belt


Set the crank to 0 degrees according to the timing marks on the damper, look on the cam pulley for a mark and line it up with the mark on the head. Put the belt on WITHOUT moving the cam or the crank.

Jan 27, 2017 | Ford Cars & Trucks

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

2 Answers

Cam Crankshaft timing


8 degrees before tdc

Mar 10, 2010 | 1983 Chevrolet Chevy

3 Answers

1991 toyota p/u timings not right. If crack is at


If the crank is lined up to the mark, it is at TDC, meaning cylinder number 1 piston is at TDC.

Both cam pulleys should have marks, they just look a little different.
Here are the diagrams to help out.

c98bc39.gif
a1eb838.gif

Sep 12, 2009 | 1991 Toyota Pickup

1 Answer

1997AudiA6Quatro2.8L-aligning cam and crankshaft for timing belt


You must find the cam lock bar and crank lock pin to do this job properly, otherwise you can bend some valves and that becomes expensive..the front crank damper has a mark to line up with a mark on the timing cover for #1 TDC, but the cam lock bar is what aligns the cams into position. The crank lock pin is helpful but not 100% necessary...

Aug 15, 2009 | 1997 Audi A6

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

1 Answer

I AM REPLACING THE TIMING BELT ON MY 1999 DAEWOO WITH 1.5 LITRE ENGINE AND NEED TO KNOW THE TIMING SPECS SO I CAN SET THE TIMING ON THE CRANKSHAFT....ALSO I NEED TO KNOW THE T.D.C. ON THE #1 CYLINDER FOR...


single cam
cam at 12 o clock
crank at 6 o clock
marks in rear timming cover

twin cam
cams marks face each other 3 & 9 o clock
crank at about 6 o clock mark in cover
all marks are visible on gears and covers

May 15, 2009 | 1999 Daewoo Leganza

1 Answer

Point tha chain timer altima 94


if you mean the timing chain then on your crank gear and your cam gear there will be a mark on each sometimes they look like a dot the dots need to look like this for perfect timing ( . . ) this will be there closest position. Your crank turns once all the way around (360 degree) and your cam gear will do two complete revolutions to the one of the crank gear. so when you set your marks as above when you turn the crank one half turn the mark on the crank gear will be at the bottom and at the same time your cam gear will have made one complete revolution, so when you turn the crank another half turn your cam would have turned again a complete revolution and the two marks should be at their closet point again.

Jan 08, 2009 | 1993 Nissan Altima

1 Answer

NEED TIMING MARKS 2.0L DUAL CAM FORD CONTOUR


the cam marks are on the cams under the valvecover the crank has a mark o nthe timing cover that you need to line it up to

Jan 02, 2009 | 1996 Ford Contour

Not finding what you are looking for?
1996 Ford Contour Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...