Question about 2001 Volvo V70

1 Answer

Car judders when in drive also switches on cetre console with S E and W flash. also an arrow flashes on bottom right of instrument cluster

Posted by on

  • duartej May 11, 2010

    are you talking about a compass with the S E and W? Also when you say judders, are you accelerating or braking?

  • madmax_83 May 11, 2010

    Is the car a stick or automatic??? Also, the juddering could be a broken motor mount or transmission mount. If the car is a stick the arrow could be a shift light.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 32 Answers

Your automatic transmission is in limp mode. It detected a problem and set itself into limp mode which is basically the same as W or WINTER mode. It's computer should have stored a code that will tell the service technician what caused the error. Sometimes shutting the engine off and restarting will reset the transmission.

Posted on Jan 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will cause a 1999 Pontiac Sunfire to not go into the extended learn mode when replacing the ign lock assembly .


Did you clear codes ? . All codes in the theft deterrent module must be cleared for a relearn.
PASSLOCK Changing - Components Description
Important: Due to component variability, the vehicle theft deterrent (VTD) system must have the learn procedure performed regardless, if the vehicle starts on the first ignition cycle after a VTD repair.
All codes in the theft deterrent module must be cleared for a relearn.
Engineers design the Passlock™ system in order to prevent theft even if the various theft deterrent parts change. The Tamper mode will engage if any of the following components change:
• The Passlock™ lock cylinder
• The instrument cluster
• The powertrain control module (PCM)
If you replace any of the above components, the system will enter the long tamper mode. If the system enters the long tamper mode, ensure that the system completes a long tamper mode cycle. During the long tamper mode cycle, the THEFT indicator will flash for the full 10 minutes. The instrument cluster and the PCM require the full 10 minutes in order to complete the learn cycle. Ensure that the ignition switch remains in RUN until the indicator stops flashing. If you turn the ignition switch before the indicator stops flashing, repeat the long tamper cycle from the beginning.
Are there any codes ?
Problem
Action
The THEFT SYSTEM indicator will not light under any circumstances.
Replace the instrument cluster.
For Chevrolet vehicles, refer to Instrument Cluster Replacement .
For Pontiac vehicles, refer to Instrument Cluster Replacement .
Multiple indicators light continuously.
Test for a loss of serial data. Refer to Data Link Connector.
Instrument cluster DTC B1021 sets.
The DTC indicates a loss of powertrain control module (PCM) serial data. Refer to Data Link Connector.
Instrument cluster DTC B1022 sets.
The DTC indicates a loss of SIR serial data. Refer to Data Link Connector.
Instrument cluster DTC B1023 sets.
The DTC indicates a loss of ABS serial data. Refer to Data Link Connector.
PCM DTC P1601 sets.
The DTC indicates a loss of PCM serial data. Refer to Data Link Connector.
PCM DTC P1629 sets.
The DTC indicates PCM Theft Deterrent failure. Refer to the appropriate diagnostic table in Engine Controls.
Instrument cluster DTC B1011 sets.
Refer to DTC B1011 Passlock Cyl Data Shorted This Ign Cycle .
Instrument cluster DTC B1012 sets.
Refer to DTC B1012 Passlock Bad R-code This Ignition Cycle .
Instrument cluster DTC B1013 sets.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle .
Instrument cluster DTC B1014 sets.
Refer to DTC B1014 Passlock R-code Unprogrammed .
Instrument cluster DTC B1015 sets.
Refer to DTC B1015 Passlock Cluster Fail Enabled .
Instrument cluster DTC B1017 sets.
Refer to DTC B1017 Passlock R-code Learn Failed .
The indicator flashes and no instrument cluster codes are set.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle (the diagnostic table for DTC B1013).

Apr 07, 2017 | 1999 Pontiac Sunfire

2 Answers

I have a 2007 Eddie Bauer Explorer how do I fix the message center that keep flashing circle slowly then it flashes calibrate complete.


Do you have base instrument cluster) or high series instrument cluster) ?
Symptom Chart Condition Possible Sources Action
  • The message center is not operating correctly (base instrument cluster)
  • Instrument cluster
  • OBSERVE the operation of the message center when pressing the TRIP/SELECT button. Does the message center display change when the TRIP/SELECT button is pressed?
    • If the message center display changes, the system is operating normally at this time.
    • If the message center display does not change, INSTALL a new instrument cluster. REFER to Section 413-01 . TEST the system for normal operation.
  • The message center is not operating correctly (high series instrument cluster)
  • Message center switch
  • Instrument cluster
  • Go To Pinpoint Test A .

Jan 24, 2015 | 2007 Ford Explorer Eddie Bauer

1 Answer

Flashing inst cluster


THE PARKING ASSIST MODULE ENABLES THE RIGHT SIDE OF THE INSTRUMENT CLUSTER

Apr 25, 2013 | 2004 Lincoln Town Car

3 Answers

Only Rt turn signal works no matter if switch is in Lt or Rt position


The multi-function switch could be defective. The L/R position signals go to the instrument cluster then they are bussed on computer data lines to the front control module to develop the outputs that light the turn lamps. The defect could be in the instrument cluster, the front control module, or even the PCM

Nov 05, 2012 | 2008 Mitsubishi Raider

1 Answer

Can't set clock for dst


If you have the command display unit first adjust time on command it will automatically take by instrument cluster if don't have the command, First ignition on, then have a look on steering wheel you have two multifunction switch group on your steering at left and right, press right arrow key on left switch group, keep eye on instrument cluster display then get setting menu and press OK key on same switch group, then use up and down arrow keys to select time then press OK, and now you have to operate right hand switch group + or - key for increase or decrees time.adjust the time or date you need then press OK, is this information helped you?

Nov 14, 2010 | 2007 Mercedes-Benz ML350

1 Answer

How to read codes for 2001 Eldorado Cadillac


Take a look at your air con controls on the centre console.

You will see an "OFF" button and to the right of this you will see a toggle switch with an up arrow with the word "PASS" just below it.

Simultaneously press the "OFF" button and the up arrow together for three seconds or so and release when you see the instrument cluster lights come on.
You are now in diagnostic mode.
Read the codes from the digital display on the instrument cluster.
Have a pen and note pad ready to write down the codes.



May 18, 2010 | 2001 Cadillac Eldorado

1 Answer

How to get to bulbs behind instrument panel assembly.(All blinkers and lights work fine on the outside lenses of the car) Right turn signal arrow is not illuminating or flashing during a right turn. Need...


  1. Disconnect the negative battery cable.
  2. Remove the meter hood.
  3. Remove the instrument cluster.
  4. Turn the socket counterclockwise to remove the bulb.
  5. Install in the reverse order of removal.


Nov 08, 2009 | 1999 Mazda 626

1 Answer

The instrument cluster lights will flash


check the positive ground wire to your fuse box if it is loose it can cause the lights to flash. thanks to ranye for the help

Aug 28, 2009 | 2008 Chrysler Pacifica

1 Answer

Electrical issue is causing stereo, heater and instrument cluster


Possible solutions include:

1. Relay or Circuit Breaker
2. Bad Ground or a broken Ground.

Please tell me if the instument cluster is working fine or is there lights that flash on that as well.

Feb 03, 2009 | 2003 Ford Expedition

1 Answer

1993 chrysler instrument cluster lights out, headlights flash


sounds like you have a problem with your alarm system. likely the ignition switch is the problem.

May 15, 2017 | 1993 Chrysler Concorde

Not finding what you are looking for?
2001 Volvo V70 Logo

Related Topics:

839 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...