Question about 2003 Pontiac Bonneville

1 Answer

2003 pontiac bonnyville headlight installation

I just had after market headlights installed for my 2003 bonny. It appears that the lights a e shiing too high up. How to I check this?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Unless you have a headlight re-alignment tool, take it to a shop that can check and if nessesary align your lights.

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing halo and hid lighting in an after market headlight


    Aftermarket Projector Headlight How To Replace HID ...

    store.ijdmtoy.com/Aftermarket-Projector-Headlight-HID-Installation.../5...
    Here are some quick tips and instructions on how to install an aftermarket HIDConversion kit into an aftermarket projector headlight assembly. ... Aftermarket projector headlights look almost like an OEM headlight with the exception of the wiring and design. You would need to remove ... images for Replacing halo and hid lighting in an ...

Nov 24, 2015 | 2000 Jeep Grand Cherokee

1 Answer

How do I adjust my Raxiom chrome projector headlights (halo) on my 2005 v6 mustang


a lot easier than you think . there are adjusting screws just look it over a bit and you will see . the light screws I'm sure

Feb 21, 2015 | 2005 Ford Mustang V6

2 Answers

How do you remove the headlights off a Pontiac grand am 2004


Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
  1. Open the hood.
  2. Remove the front air deflector.
  3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
  4. Lift up the headlight retainers to release the housing.
  5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
  6. Disconnect the wiring harness from the headlight assembly.
  7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
  8. Remove the bulb(s)/socket(s) from the headlight assembly.
To Install:
  1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
  2. Connect the wiring harness to the headlight assembly.
  3. Position the headlight assembly to the mounting panel.
  4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
  5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
  6. Install the front air deflector.
  7. Close the hood.
prev.gif next.gif

Feb 02, 2011 | 2004 Pontiac Grand Am

1 Answer

Flip up headlights won't stay up


Hi
Check the connections to the back of the motor and spray all around the mechanism with wd-40 this may free it up they get tight after a while and start to seize the motor then you will have to replace that aswell.

Dont be shy with the WD-40 I have had this fault twice and both times it worked.

If it is something else please let me know
Regards

Dan

Jan 22, 2010 | 1988 Pontiac Firebird

1 Answer

Headlight replacement on a 1991 pontiac grand am


Sealed Beam Type
  1. Disconnect the negative battery cable.
  2. Unfasten the headlight bezel attaching screws, then remove the bezel.
8ed2813.gif
Remove the headlight bezel

To avoid turning the vertical or horizontal aiming screws, refer to the illustration before removing the headlight retainer.
  1. Unfasten the headlight retainer attaching screws, then remove the retainer.
e11bb51.gif
Remove the headlight trim screws then...

67522f3.gif
... pull the trim off while holding the bulb

4. Pull the headlight out, then carefully detach the electrical connector.

8d80048.gif
Pull the bulb out far enough to disconnect the wiring


To install:
  1. Attach the electrical connector to the new headlamp.
  2. Place the headlamp into the socket.
  3. Install the retainer, then tighten the attaching screws.
  4. Connect the negative battery cable, then turn the headlight switch on, to be sure the headlights are operating.
  5. Install the headlight bezel and secure using the attaching screws.

Jan 18, 2010 | 1991 Pontiac Grand Am

1 Answer

Trying to replace light bulbs, front and rear


No usually for GM vehicles there are two pins on the headlight that you pull out and up. they are L shaped upside down. If not there are bolts holding the headlights on. But no special tool needed, it is a simple job, once the headlights are off twist the bulb counter clock wise, if they have a notch depress it and remove the bulb unhook it from the harness and you are done. Installation is reverse of removal.

Jul 06, 2009 | 2003 Pontiac Montana

Not finding what you are looking for?
2003 Pontiac Bonneville Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...