Question about 1996 Nissan Quest

1 Answer

Nissan Quest 1996 minivan

How do I replace the CV joint on the passenger side of a Nissan Quest 1996 minivan, and is it possible to download a manual for this vehicle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

You need to remove the lower balljoint and the center nut and it should come right out. use pb buster or wd-40 on the splines. they tend to rust up

Posted on Oct 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2012 Nissan Quest side doors will not open with the buttons. The remote and dash controls both work. This happened immediately after having the car cleaned inside and out.


Is there a switch that turns off the sliding door switches? It is usually next to the door switches. Its possible that the detailer was trying to turn off the interior lights to keep from running the battery down and inadvertantly turned the switches off. My Caravan and my Olds Silhouette had this feature. Next check the fuse (s). If not I would suspect that possibly some type of cleaner or protectant may have gotten sprayed into the switches..

Jul 13, 2016 | 2012 Nissan Quest S Passenger Minivan 3.5L...

1 Answer

Need vacum diagram intake manifold/2002/mercury villiger


the following is for a nissan quest, but they had a joint venture between Nissan & Ford to make this generation minivan ~1999-2002


(i have a mix of ford and nissan stamped parts in my minivan!)


http://www.nicoclub.com/FSM/Quest/2002_Quest/ec.pdf

start at page EC-22

credit and kudos for Greg who keeps nicoclub site running!

Mar 26, 2015 | 2002 Mercury Villager

1 Answer

I have a 93 Nissan quest minivan if the front end sounds like it is hitting something when i turn right would i only have to change the passenger side cv axle?


Could be axle, wheel bearing or both. I would recommend to change them both. Every time the shaking occurs, it damages both. Good luck.

Jul 30, 2012 | 1993 Nissan Quest

1 Answer

1999 Nissan Quest while turning left it makes a clicking sound. What could be wrong.


it sound to me like you have a cv joint worn out. these are located on either end of your driveshafts and dependant on where and what side the noise is will indicate which 1 needs replacing. usaually caused by a split cv gaitor leading to an ingress of dirt and water.

Apr 29, 2012 | 1999 Nissan Quest

1 Answer

Broken lug on rear passenger wheel. How do


TAKE VECHICLE TO A TIRE REPAIR SHOP LIKE SEARS OR OTHER TIRE SHOP IN YOUR AREA.THEY CAN PRESS STUD OUT OF BEARING WITHOUT DAMAGING IT AND PRESS IN A NEW ONE WITH NEW LUG NUT.

Jun 07, 2010 | 2005 Nissan Quest

1 Answer

How to replace or install a nissan quest 1997 axle


two axles, different for ach side. Passenger side has a carrier on the half shaft, driver side is one solid link. Loosen lug nuts, the you need a 36mm socket to loosen the center nut on the drive shaft, same for both sides. Remove the cotter pin and retainer before loosening the center nut. Jack up the vehicle and secure with jack stands. Remove wheels. Remove brake calipers and tie up out of the way. Loosen and remove lower strut bolts (2) and lower ball joint bolts (3). Swing center knuckle out and off the drive shaft. On passenger side, loosen carrier bolts (3) halfway up the drive shaft, above the exhaust pipe and crossmember. This is a pain on the 94, but easier on later models. The passenger shaft has two half shafts joined at the carrier. No retainer clip is used, so pull on the end of the shaft and it will come out. Iff the inner CV boot is puked, it will probably come out in two pieces. You may have to use a large screwdriver to pry the inner shaft out of the transaxle. The driver side does not use a carrier and will come out with a strong pull. It does use a retainer clip on the inside end of the driveshaft. You can get new driveshafts with cvs as an assembly at most auto parts stores Be sure the new driver side shaft has the new retainer clip on it. Assembly is reverse of dissassembly, but make sure to tighten everything up good.

Feb 26, 2010 | 1997 Nissan Quest

1 Answer

2007 Quest: The passenger side sliding door will not open


There is a wiring problem on your drivers side passanger door switch.

May 10, 2009 | 2007 Nissan Quest 3.5 Minivan

1 Answer

1995 nissan quest minivan gxe v6 - noise under the hood


low or no oil pressure... check the level of the oil .. add if necessary and have the oil pressure checked

Robert

Jan 26, 2009 | 1995 Nissan Quest

Not finding what you are looking for?
1996 Nissan Quest Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...