Question about 1995 Nissan Pickup

1 Answer

95 nissan Truck

I have a 95 Nissan (4 cylinder - 5sp) with a little over 400K. It began to stall when the clutch is depressed and will not idle. Now, it has lost power and will only turn about 3000 rpm. my friend suggested that it may have something to do with choke, any ideas??

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 193 Answers

Your truck should have fuel injection, so there would not be a choke. Your best bet is tostart with simple items. Sounds like you have a main line fuel filter clogging up. And if that is the case, you need to have your injectors flushed.
Bill

Posted on Nov 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car starts hard then idles roughly for 2-3min then stalls and dies


It sounds like some thing you have done if the fault started after the tune , did you check the gap on the new plugs, check the firing order as it may be messed up . 4 cylinder 1342 6 cylinder 153624 in direction of rotation.

Dec 03, 2015 | 1996 Nissan Altima

1 Answer

How do I bleed a hydrolytic clutch on a 1989 Nissan d21 truck 4x4


There is a bleed valve on the slave cylinder that is on the transmission bell housing. Use an 8 or 10 mm wrench and loosen the valve, then snug it just hand tight. Now have someone depress the clutch pedal. As the pedal is depressed, loosen the bleeder and let air or fluid out. Close the valve as the pedal hits the floor, then repeat until a steady stream of brake fluid comes out of the bleeder as the clutch is depressed.

In many cases, the hydraulic clutch will gravity bleed when the bleeder valve is open. This is especially true if the fluid line from the clutch master cylinder (on the firewall) down to the slave cylinder is not bent up or around any objects, but is pretty much a straight drop down to the slave cylinder. If it won't gravity bleed by just opening the valve, have a helper work the clutch pedal as described. Remember to close the bleeder before letting the pedal up, so that air won't be sucked back in through the bleeder valve.

Apr 26, 2015 | Nissan Cars & Trucks

1 Answer

Hot to fix a clutch that goes all the way to the floor


Check your clutch master cylinder's fluid,it's located under hood in right corner,if low or empty,then your slave cylinder is bad and leaking,it's connected to side of transmission.Here's a link. Repair Guides Clutch Clutch Release Cylinder AutoZone com Here's the part. Duralast Clutch Slave Cylinder 12425 1992 Nissan Datsun D21 Truck 2WD 4...

Jan 14, 2014 | 1992 Nissan Pickup

1 Answer

1988 Nissan 300zx 5 speed clutch peddle does not


Sounds like you have a leak in your clutch master or slave cylinder. I had the same problem. They are not too expensive at kragen or auto zone. The master cylinder is located on the right side of your engine closest to the driver. Open the cap and check if theres fluid. If its low or empty then there might be a leak. The slave cylinder is located on the passenger side under the car bolted to the transmission. That could be leaking or not working properly. I would replace both if you can. Hope this helps.

Sep 24, 2011 | 1988 Nissan 300ZX

1 Answer

Nissan clutch problem


If your not able to shift into any gear that means your clutch is not engage/disengaging. Check for fluid leaks, you said topped off and fluid levels were low? It sounds like you have a Slave cylinder or master cylinder leak, if its leaking its bet to replace both.

Apr 27, 2009 | Nissan Sentra Cars & Trucks

1 Answer

Hard to depress the brakes and when depress the engine idle chang


It sounds like you have a bad power brake vacuum booster.It is the big round metal cylinder behind the brake master cylinder where you add fluid.

Mar 06, 2009 | 2000 Nissan Xterra

1 Answer

91 nissan pickup 4 cyl.


Did you or replace the throw out bearing ? Or the clutch has to be adjusted. does it have a hydraulic clutch ? These have to be bleeded like the master cylinder of the brake sytem.

Aug 13, 2008 | 1991 Nissan Pickup

Not finding what you are looking for?
1995 Nissan Pickup Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...