Question about 1998 Saturn SL

1 Answer

Help me with how to replace a head gasket and starter

My starter went out because it got too hot because I blew my head gasket. How do I locate and replace these?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 208 Answers

Replacing a head gasket is not a DIY job, unless the person has plenty of experience, knowledge, and the proper tools. The fact that a person would even ask, "How to replace a head gasket", would indicate to some that they should not trying to do that repair.

To replace a head gasket you must remove the intake manifold, exhaust manifold, valve train, and then the head. This is very involved and requires disconnecting lots of sensors and the ignition system. The head must then be checked to see if it is warped, or cracked, and repaired if necessary. You must then know how to put all this back together and torque all the bolts in the proper sequence. This takes training and skill which the average shade tree mechanic does not have.

There is a difference between say a over head cam (OHC) engine and a internal cam engine. And then if it is a V6 or V8 then both head gaskets must be replaced even if only one blew. And last but not least, you have to find out if there is other engine damage and what caused it to blow the gasket in the first place. Definitely not for an amateur.
The best answer to this question: Take it to a professional.

The second-best answer: Get a repair manual and follow directions. A repair manual does not provide the training necessary to do this repair correctly, and not near enough information, but it can provide more info than can be written out in an answer like this.
Below is the best answer we can provide in this format.

* Make sure you have a torque wrench and the correct torque specs for your vehicle

Parts
Exhaust flange nuts and bolts
Head Gasket (preferably OEM)
Ten head bolts
Two valve cover end seals
Tube of RTV silicone

Disassembly
1. Disconnect the battery negative terminal
2. Drain the cooling system
3. Raise the front of the vehicle and support it with jack stands .
4. Remove the two 13mm exhaust bolts holding the exhaust pipe to the exhaust manifold, lower the vehicle
5. Remove the air cleaner assembly
6. Remove the upper radiator hose
7. Loosen the 13mm nut holding the dipstick tube bracket to the thermostat housing and remove the coil (if it is attached to the thermostat housing) and unplug the coolant temperature sensor
8. Remove the spark plug wires from the plugs, remove the distributor water shield and the distributor cap (this step is so you don't damage the distributor cap).
9. Remove the two uppermost 15mm-head bolts from the top of the a/c , alternator bracket where it attaches to the head and unplug the single wire temperature sending unit
10. Remove the upper half of the timing belt cover
11. Remove the valve cover
12. Disconnect the wiring harness connector that is just to the right of the throttle body
13. Disconnect the throttle cables from the throttle body and remove the two 10mm head bolts holding the bracket
14. Disconnect the vacuum lines from the throttle body
15. Disconnect the fuel lines - NOTE : The fuel lines may be under pressure , use extreme care when removing them
16. Disconnect the throttle position sensor connector and the EGR valve connector (if equipped)
17. Carefully lift up the throttle body wiring harness , the fuel lines , and the vacuum lines together and use a bungee cord to hold them out of the way
18. Remove the ground strap that is attached to the intake manifold from the fire wall
19. Remove the 15mm-head bolt holding the battery ground cable to the engine
20. Disconnect the vacuum hose from the power brake booster and the heater hose from the intake manifold left side
21. Use two plastic tie straps to secure the timing belt to the camshaft pulley and remove the pulley . Hold upward tension on the pulley and secure it with a bungee cord to the right hood hinge - NOTE: be sure to hold the upward tension with the bungee cord so the timing belt doesn't jump a tooth on the lower pulleys
22. Remove the head bolts and lift the head off the engine block . (I suggest having an assistant help to lift off the head) With the head removed , carefully check the head casting for signs of cracks. Also use a straight edge to check the head casting for warpage (maximum allowable warpage is .00
23. Clean all the head gasket mating surfaces and wipe clean with a little brake cleaner on a rag. Use a round plastic bristled brush to clean out the head bolt holes in the engine block and blow them out with compressed air .

Reassembly
1. After the gasket surfaces are prepared, set the new head gasket in place and CAREFULLY place the head into position, take extreme care not to place the head on the head gasket until it is in the proper position.
2. With the head in place, install the head bolts. You will need to tighten the head bolts in a circular pattern starting from the center and working your way out. I recommend hand tightening all the bolts before beginning the torque sequence. Head bolt torque: For older style 10mm head bolts : 35 - 45 - 45 - and a 1/4 turn; For newer style 11mm head bolts : 45 - 65 - 65 - and a 1/4 turn
3. Use the two rubber valve cover end seals and a bead of RTV silicone to reseal the valve cover.
4. Do Not let the silicone skin-over before setting the valve cover into place and tightening the bolts, also be sure that both mating surfaces of the valve cover are clean and oil free .
5. After the head is reassembled you will need to reset the base timing to specs. You will also want to double check the timing belt position . Use a variable timing light and set the timing mark on zero degrees . Save the setting on the timing light and shine it through the inspection hole in the top of the upper timing belt cover . If the belt timing is correct , you will see the oblong hole in the camshaft sprocket centered in the inspection hole .


Hope my info solves your problem,
Thanx for using fixya......

Posted on Oct 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Sebring overheated, wont start


Is it possible you blew the head gasket and now you don't have compression on all cylinders ?

Jun 25, 2013 | Chrysler Sebring Cars & Trucks

1 Answer

Ford Ranger overflow tank bubbling and overflowing, running hot, white smoke, after water pump failure.


The smoke could be the water boiling. Although it is possible that you blew the head gasket, if the vehicle overheated badly, It is also possible that you still have some air in the system. Replace the thermostat and seal /gasket and run the vehicle while adding coolant. Do not install cap on until both houses upper and lower are hot to the touch. This is an indication that the thermostat opened and coolant is actually circulating. Good luck.

Mar 13, 2012 | 1992 Ford Ranger

1 Answer

I have a 1998 Ford Windstar and the water pump went out so i had that fix the same day I had the spark plugs done after that car started made all kinds of noises then ran hot again after that the car...


If it ran hot when the water pump went out, it may have melted some of the interior parts and so ruined the engine. As it was driven on, it probably blew the head gasket. You may fix it simply by replacing the head gasket or you may need a complete engine overhaul, depending on how hot it got and how much damage was done. The only way to know for certain is to go into the engine to assess the damage.

Nov 08, 2010 | 1998 Ford Windstar

1 Answer

Engine was ruuning hot pd 800. to have it repaired 5 days later the head gaskets blew. is that normal?


Head gasket blowing is not normal. Need a clue as to what the 800 bucks went to doing, to know if related or not. If the head gasket fails, just replacing the gasket does not fix the issue, the gasket is a victim. There will be something else wrong, like warpage or cracks. AND this may not be the issue causing the overheating...

Oct 06, 2010 | 2002 Chevrolet Impala

2 Answers

Engine propblem


usually when you get white smoke its because ur head gasket blew mixing antifreeze and engine oil look at ur oil and see if its a milky white color.car will not start beacuse ur loosing compression threw the gasket blowing..

Mar 22, 2010 | 1997 Mitsubishi Eclipse

2 Answers

97 mustang overheating and blowing cold air


Get a compression check to find out if you have a bad head gasket, I have a 96 with the 3.8L that had the same problems at first. then it started to blow out antifreeze thru the expansion tank, the head gasket finally blew the rest of the way going down the highway

Dec 04, 2009 | 1997 Ford Mustang Cobra

1 Answer

Waterpump went out and engine got real hot and blew upper radiator hose replaced waterpump and hose now it wont fire


It is very likely the overheating has blown the cylinder head gasket and coolant is getting into cylinders or compression is leaking from cylinder to cylinder or both, you will need to remove the cylinder head and have it checked for warp-age and shaved flat by a machine shop if ness, and replace heat gasket.

Apr 07, 2009 | 1997 Mazda Protege

Not finding what you are looking for?
1998 Saturn SL Logo

1,093 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...