Question about 1991 Jaguar XJ6

2 Answers

1991 XJ6 ignition barrel replacement

I need to replace the ignition barrel on my 1991 XJ6 anyone know how to do this?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 100 Answers

Remove the steering column panels and turn the key to position 1, there is a hole that is on the steering lock assembly that you need to use a pick or similar rool to puch in the hole and release the spring tension, then the barrel slides right out and make sure you put the new barrel to position 1 and it will slide right in and "click" in place. Put the panels back on and your set to go.
JPTCAT

Posted on Oct 15, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

$15.00 manual from auto zone explains perfectly in layman terms. gotta have if you like your car.

Posted on Oct 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition lock cylinder removal xj6 1997


To remove the ING barrel put the key in turn to position one.on the side of the colum round the barrel there is a hole you need to press the button down that is in this hole. If the key is not in or in the wrong position the barrel will not pull out.

Dec 07, 2014 | 1997 Jaguar XJ6

2 Answers

How to make a shaved key for 1991 Buick century?


replace the barrel in the ignition lock and you will get 2 keys already cut to the new barrel. If there is an immobiliser included in the system you will have to get the new keys programmed to the CPU in the ECM of the car

Sep 03, 2014 | 1991 Buick Century

1 Answer

Bolt torque sequence on 1991 jaguar xj6 4.0 intake manifold?


intake manifold or head gasket? i know head gasket need a sequential order followed by how many degrees and Lbs of pressure. if its on the intake i doubt it needs an specific torque. just try not to crack the intake manifold since its made of plastic.

Oct 29, 2012 | 1991 Jaguar XJ6

1 Answer

Power on both sides of coil contionious no power to plugs won't start 91 xj6 fuel pump also not working unless use a jumperat fuel pump relay.


Sounds like the problem I'm having. No noise coming from the fuel pump when the ignition is switched on. I've read that there is an inertia switch that, when activated, stops the fuel pump from working. Haynes says it's behind the passenger side kick panel, but I don't see it on my 1991 XJ6 (XJ40). Do you know where it is?

Nov 12, 2010 | 1991 Jaguar XJ6

2 Answers

Replacing front brake pads on 1991 jaguar xj6


I always use a c-clamp to push the piston in with. you won't be able to replace the pads unless you push the piston in.

Jun 28, 2009 | 1991 Jaguar XJ6

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

1 Answer

Ignition key jammed in start position,managed to stall engine,disconnect battery,key will not return to off position even with a little help with pliers,any ideas???


Remove ignition barrel covers and as your wiggling the key knock the ignition barrel with appropriate tool to try and loosen whats jammed Either way have to take covers off to remove barrel and replace.

Oct 19, 2008 | 1991 GMC Sierra

1 Answer

Starter


Bad ignition switch or starter seleniod

Sep 06, 2008 | 1991 Jaguar XJ6

2 Answers

My alternator went out and I gave my only key to the mechanic who has lost the key how do I get a key made?


hi there u should try to call a lock smith they can work out your key discription from your ignition barrel and make a new one if they cannot do it at all you might have to go buy after market or genuine door locks and another igniton baral again

Jul 01, 2008 | 1991 Jaguar XJ6

Not finding what you are looking for?
1991 Jaguar XJ6 Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...