Question about 1989 Chrysler New Yorker

1 Answer

'89 crysler new yorker " power windows "

My power window will not go back up and i dont know how to take the door panel off or get the window up for good at least... can some one point me in the right direction or let me know how to do this please... thank you...

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had a similar situation with my 88 new yorker. When I powered up the passenger window, it would go so far make a growling noise and stop. I had to put one hand on each side of the glass and push the window up and this would work only if I got the window up to the growling point. Turns out it was the window regulator tape which was cracked in the middle and I had to replace it. It works fine now.

Posted on Sep 07, 2009

  • heypapa Sep 07, 2009

    If you still have this car and the repair is not done yet email me for more information,

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My passenger rear window in my 1991 crysler new Yorker is off track how do I put it back?.


need to remove panel to access tracks =observe which track is damaged or needs reattachment

Oct 22, 2016 | Cars & Trucks

2 Answers

Rear electric windows won't roll back up. Circuit breaker?


There is a fuse but if it is only back ones and the front work without trouble not fuse. If one window don't work could be motor. If both windows don't work probably a switch check left rear switch. Also relay space 9 in fuse box

Sep 25, 2015 | 1991 Buick Century

1 Answer

How do I put the driver side power window back on track and the door panel for my 2003 Nissan Altima 3.5SE?


R/R the inner door panel, slide the window back on track, reconnect the window transmission to the window, (or reinstall the trans) bolt everything back together (window motor, window trans to door etc.) Make sure the window is in the UP position. use the switch to raise the window & keep it up if all is back together before finally installing the door panel ( make sure the switch & other plugs are plugged in before the door panel is reinstalled.) Lights etc. Good luck

Sep 14, 2014 | 2003 Nissan Altima

1 Answer

Replace front passenger window for 2000 chrysler cirrus


most windows follow the same proceedure...
lok careful at the door pad you will see screws hidden by the inside handle (usualy 1 door opener handle) sum screws are hidden by caps / lil round covers that u pry up with a small pick tool (2 usualy by the inside pull /grab handle) sum you pry up the door switchs and can be hidden underneith) sum may be on the edges , if the lil trim panel that covers the mirror mount (may also have speaker in it )is in the way they usualy pull straight out. (clips on back) when you think all the screws are out grab the lower corner of the panel and give it a good yank this should start the panel coming off (behind you will see long plastic '1 inch ' pin type clips you may find six or 8 as you work the panel back/off) if at any point it feels like its not popping free STOP and look for a screw you missed or you will wreck the door panel!!!
power doors will have plugs the go into the switches sum realy **** to remove but careful study should reveal sum kind of release clip or tang you must lift or squeeze . set panel aside when you have it off. but keep the window switch handy you will have to plug it back in usualy twice to align the window holding screws so you can loosen or tighten them when you put the glass back in..that said the panelless door will have a plastic or foam "skin" on it carefuly peel it back ( i use a box cutter blade to cut the sticky stuff if it wont peel back easily, (sum people just cut it and tape it back on after ) this is the dust protector (keeps dust out of cabin of vehicle) once thats removed or folded out of the way plug the window switch in and run either up or down to expose the window hold bolts or clamps.IF REPLACING BROKEN GLASS now is the time to shop vac out all the glass !!!!! it will rattle in the door and drive you crazy if not .ALSO tack a small screwdriver and run it thru the window track that surrounds the door glass IF you leave glass it the track the window will break again and also makes real nasty grindy scratchy sounds. With the glass you buy from an auto wrecker (HELLO BEST PLACES FOR CAR PARTS GOING!!!) clean the glass then look at the opening where the glass goes in if the window "belt" moulding leaves only a small **** to insert the glass pull it up carefuly from one end to remove. dont bend it its not abuse friendly!! tip the glass narrowest end down , most from the outside , and slid it into the door shell,as you get farther in turn and work it into the window track !! dont drop it sometimes the regulator must be lowered down all the way to allow the glass to turn .. watch and set the glass into the holders (some glass has holes some have a track some have plastic tabs ) carefuly tighten either the bolts or clamp what ever style you see in your door!
make it snug but dont try to overtighten or you go back to shop vac !!
test window for up and down NOTE some doors the window trac extends down inside the door and must be loosend off or removed to accomodate the window going in.remember to install these back in if you have to remove them use the marks left by the screws to reset them back to propper fit test BEFORE you put it all back together.
if you are happy with your work .do the belt moulding ,replug things on or atleast pull wire thru the panel ,align the "pins" start at top edge and bang the panel back in (palm of hand punch) NOTE if sum pins stuck in door pry them out and fit them back into panel before putting it back on!! replace screws and you are done as you can tell i've done many door glass replacements most take me an hour to complete including shop vac broken glass off seat and floor n dash GOOD LUCK!!!!!

Feb 03, 2012 | 2000 Chrysler Cirrus

1 Answer

Window off-track


dont recomend it the process is a big job. start with the mirror cover 2 window switch3 pull handle 4 about ten screws in trim panel and aem rest. then unbolt window from window regulator lift out of door enough to tilt window to alighn it to trackes. then reverse for reassembly

Dec 15, 2011 | 1989 Ford Mustang

1 Answer

My 2002 jetta the door didnt lock or unlock and windows dont work and alarm is off


I appologize for not getting back to you sooner. The market place is still in developement and for some reason this afternoon when I tried to comment I could not post from my android, Ipod, or Ipad.

The only thing the two have in common are fuse 38 and the power window circuit breaker. This would be a good place to start. The fuse will be obvious if it is blown. You will need to check continuity of the circuit breaker or swap it with one that you know is good.

If the fuse and circuit breaker are good than you will need a test light or multi-meter. You will also need to remove the drivers front door panel to gain access to the power window switch and the drivers front door module. If you have this test equipment and are able to get the door panel off let me know and we will go to the next step.

Oct 08, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

How to fix drivers window.the window just feel in to the door panel. it is a power window. WHAT WOULD BE THE PROBLEM.


window came of track inside door maybe rollers came out of place have to remove door panel to access

Apr 05, 2010 | 1991 Chrysler New Yorker

1 Answer

The passenger side window on my 2001 F150 will roll down but not up?


Might want to pull the door panel off and test direct to the power window motor, to know which way to go with the diagnoses.

Good directions for removing the door panel are available at Muth ( signal mirror mfgr ). www.kwmuth.com Obviously only follow the directions to the point of getting the door panel off, no need to remove the mirrors. Just enter your truck info, and on the products page are the directions in PDF format.

The power window has a pig tail on it, that goes to the switch ( this is what it looks like remvoed ).
721d619.jpg

You can apply DC power to the pigtail towards the motor, 1 direction is up reverse polarity and the window should go down.

If the motor works this way, next is to meter the lead from the switch ( the other side of the pigtail ). One direction will have + 12 DC V, then the switch the other should show -12 DC V. If not, it would be time to test both switches.

Post back what you find with the motor test as a comment, and we can go from there.

Mar 30, 2010 | 2002 Ford F150 Regular Cab

1 Answer

My 87 honda accord 4 door power windows dont work only the driver door works the other 3 windows stop working all together


CHANCES ARE WINDOW LOCK SWITCH IS STUCK OR NEEDS TO BE REPLACED. ALL THE OTHER WINDOWS WORK OFF THAT PANEL. WHAT I WOULD DO IS TRY MOVING THAT SWITCH BACK AND FORTH GET IT MOVING AND SEE IF THE OTHER WINDOWS START TO WORK. IF THEY DON'T START TO WORK THAN CHANCES ARE YOU MIGHT HAVE TO REPLACE THE HOLE SWITCH PANEL. BUT I WOULD TRY WORKING IT BACK AND FORTH FIRST. GIVE THAT A TRY GOOD LUCK HOPE I HELPED.

Nov 27, 2009 | 1987 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...