Cars & Trucks Logo
Anonymous Posted on Dec 08, 2011

Will go in overdrive but nothing else

It will go into all gears but wont move unless its in overdrive.

4 Answers

Sam Akber

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

  • Ford Master 1,149 Answers
  • Posted on Dec 09, 2011
Sam Akber
Ford Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.

Joined: Feb 25, 2011
Answers
1149
Questions
0
Helped
330207
Points
3323

The clutch pack selonide has failed, it is leaking.

John Diehl

Level 2:

An expert who has achieved level 2 by getting 100 points

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Expert 94 Answers
  • Posted on Dec 09, 2011
John Diehl
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Dec 02, 2008
Answers
94
Questions
0
Helped
28056
Points
141

You said it just stops is engine still running or does it stall out ?
Mostly a torque converter is the prob but maybe be somthing eles please give more details Thanks

Ad

cy schousboe

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Ford Master 2,002 Answers
  • Posted on Dec 08, 2011
cy schousboe
Ford Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jun 02, 2009
Answers
2002
Questions
1
Helped
613225
Points
5980

It's possible that if your transmission was low enough on fluid this could happen but if you have fluid showing it most likely isn't the problem. For sure top it up if it's low, it may help.if there is no fluid on the dipstick add some until it shows on the stick.Once it shows full, start the truck and pull it through the gears one at a time, including 2 and L. Leave it in each gear for a few seconds and repeat back from L to park. Check the fluid again and top up. Repeat this process until the transmission stays at the full mark.

Two things come to mind, either the pump is bad or the torque converter. If it drives in overdrive that suggests the torque converter may be bad because overdrive locks the torque so the truck drives like a standard. The internal pump runs pressure inside the transmission, normally off the torque converter so if it failed the best you would get out of your gears might be a split second attempt to move the truck. In these cases you will have to take it in for repair. Hope this helps.

Paul Bade

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 1,818 Answers
  • Posted on Dec 08, 2011
Paul Bade
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Dec 13, 2008
Answers
1818
Questions
1
Helped
574899
Points
5816

The first step with any automatic transmission problem (if you haven't done it already) is to check the fluid level and quality. Inadequate or contaminated transmission fluid may result in shift failure or damage to the transmission. In particular, if the fluid is burned or has metallic particles in it, the transmission probably needs to be torn down and repaired. A clogged filter screen could also cause the problem, but this is rare unless dirt gets in or there is a worn-out part.
If you have to rev up to high rpms to get the vehicle moving, you may have a torque converter problem.

  • Anonymous Dec 08, 2011

    i rolled back in nutral and when i put it in reverse it will kick in gear but its like the emergency brake is pushed cause it just stops.

  • Paul Bade Dec 08, 2011

    '... it just stops." Does this mean the engine stalls, or does it mean the vehicle quits moving even though the engine is running when it is in reverse? This is important information.

×

1 Related Answer

Anonymous

  • 4803 Answers
  • Posted on Dec 11, 2011

SOURCE: Problem with 1988 Ford Bronco II.will go in overdrive but nothing else

I appreciate your request for my help. However, for either personal or technical reasons I am unable to assist you at this time.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 bmw x5 3.0 wont move in drive

Check and see will it move in low or reverse. If it wont move ONLY in drive and will move in other gears, your overdrive clutches are destroyed and the computer has placed the vehicle into "limp home" mode. meaning you cannot hurt it any more than you already have. If it wont move in ANY gear, put some tranny fluid in it. Start it and put in "N" with the e-brake on and check the fluid level with the dipstick.
0helpful
1answer

Truck wont move tranny fuse?

run fault codes and check TCM problems.
1helpful
2answers

I have a 1993 nissan pathfinder automatic transmission and it will not move in first gear.it willl move in all other gears,in drive it wont shift out of second unless i push the overdrive button,what

check ecu fuse.your problem could be vechicle speed sensor also. if you dont see any ecu check engine light fuse either blowed or bulb burned out.but if ecu not working vechicle wont shift correct.
0helpful
1answer

Problem with 1988 Ford Bronco II.will go in overdrive but nothing else

I appreciate your request for my help. However, for either personal or technical reasons I am unable to assist you at this time.
0helpful
1answer

My 96 ford probe is stuck on overdrive everytime i put it inot drive or 1st or 2nd gear if im at a stop it wont start to move until 2000rpm and idk all that it does when i hit the button is stay on and the...

You have overdrive cancel soleniod problem. What it does, when you hit the overdrive buttom it activate the overdrive off and on. You should have it check.
0helpful
2answers

95 GMC Sierra 4L60E will not shift down to 1st or up to 4th.

no power stuck in 3rd gear electric shop unless youve burnt it up good luck...www.TransmissionGarage.com
0helpful
1answer

95 NISSAN PICK UP WONT MOVE IN DRIVE

Test the transmission module. It controls everything the transmission does, the timing of shift points, gear selection, overdrive, etc
1helpful
2answers

Truck wont shift automatic. stays in 3rd gear. can shift manually

either repair or replace the transmission...sounds like the sensor went out
Not finding what you are looking for?

205 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...