Question about 1996 Chevrolet Suburban

2 Answers

Removing tranny remove trany

Posted by on

  • 2 more comments 
  • gmichael Oct 03, 2008

    yes it is a 4x4 and 350 engine.

  • gmichael Oct 08, 2008

    i was wondering on the exhaust pipe that come from each of the motor, and crosses over the tranny do I remove them,it might get on the way when lowering the tranny. thanks a lot

  • Juan Guillen May 11, 2010

    Is your trans. 4X4 or 4X2, and the engine size.

  • Juan Guillen May 11, 2010

    Can you give me the Engine size and if is 4X4. To give the right steps.

×

2 Answers

Just one =more question, the two tubes from the transmission cooler are on the side of transmission,, I notice they have a different fitting like plastic and they do not have the threads like others how do I disconnect them and if they will not break once they pull out , thanks for all the help also,

Posted on Oct 10, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

Ok..
This is the prosses to remove and install your Transmission.

1---Disconnect negative Battery cable. Remove Air cleaner. Disconnect shift cable from Transmission. Raise and support Vehicle. Drain Transmission fluid. Disconnect shift Linkage. Mark rear drive shaft for installation reference and fremove from vehicle. Mark front drive shaft and Remove from transfer case.
Warning.. ALWAYS relieve fuel pressure before disconnecting any fuel injection related component DO NOT allow fuel to contact electrical components.

2-- Relieve fuel pressure, and remove fuel lines from the Bracket support at catalistyc converter
And remove the bracket. support transmission with transmission jack or any compatible.
Remove transmission crossmember.
NOTE .. DO NOT stretch or damage any cables, wires or other components when lowering transmission.

3-- Lower transmission far enough to provide clearence for other components. remove dipstick tube and seal. cover opening in transmission. remove speedometer harness. remove electrical connectors from transmission. remove cooler lines, and cap all openings. remove starter motor.

4-- Remove transfer case shifter and move it aside, Remove transmission support braces. Note braces locatoin for installation. Remove converter housing cover. Mark flexplate( flywhell) and Torque converter for alingment during installation, Remove flywheel to torque converter BOLTS.

Remove transmission to Engine BOLTS. note location of any brackets or clips and move them aside. Slide transmission straight back, off locating pins, remove transmission from vehicle.

6-- To install, reverse removal procedure. Torque converter must be against flywheel and rotate
FREELY by HAND, ensure all reference mark aling. and tighten all BOLTS..

NOTE. In some cases is nessesary remove the Transfer case before the transmission.
The transfer case is attached at the transmission with six Bolt .....


OK... I hope this help on your question.
Thank yuo for use fixya...

Posted on Oct 07, 2008

  • Juan Guillen Oct 09, 2008

    On your question about the Catalystics or crossover pipes.



    I can do without remove the exhaust pipe. But on a LIFT machine.

    I you think its nessesary to remove for get more space. do it.

    Spray a little WD40 at the BOLTS and NUTS.



    Ok.. I hope this help .



    Thank you.

  • Juan Guillen Oct 14, 2008

    Sorry if I'm late.



    To remove the cooler lines.

    slide the Plastic cover of the fitting.

    And you will see a C - Clip ring around the fitting. Remove the C-clip or ring..

    And the line will come out with a little force.

×

3 Suggested Answers

dustyboner
  • 331 Answers

SOURCE: how do i remove the tranny away from engine

i think this is what your missing.
hope it helps

f8fa58c.jpg
9a9284c.jpg
85e0fd6.jpg

Posted on Jul 17, 2008

  • 1168 Answers

SOURCE: i am pulling a tranny

Hello Lora.

There are two locating pins that are for making sure the transmission and the engine are aligned.
These pins fit quite tight and will often seize in the holes.
If all the bolts are removed you may need to use a little force to separate the two halves.
Spray a little rust remover agent on the locating pins and let it soak.
Wiggle the transmission vigorously (make sure it doesn't fall on you).
If that doesn't loosen it you may need to pry them apart.
If you would like a little more help, ask me here in comments.
Thank you.

KL

Posted on Feb 21, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission line is leaking where it goes into trany how do i change it they are on top of trany


You will need to let the tranny down, unfortunately. BUT, it doesn't need to come out. You didn't mention if yours is 2 or 4wd, so I'll give a hint on both. Remove the rear driveshaft on a 2wd, and put your floor jack under the rear crossmember. Take the bolts out of the crossmember and slowly let it down. The tranny will drop more than enough to see if you need to replace any lines or fittings, as well as give you room to do that.

4wd is a little more work, but take BOTH drive shafts out and put the jack under the transfer case. remove any bolts holding it to the frame, then let it down. Everything else will go same as a 2wd.


Another way to access the top of the tranny, is to cut a door in the floorboard above the lines. Not recommended on a nicer machine, but works on older beater trucks!

I hope this was helpful to you.

Jul 02, 2014 | 1991 Chevrolet Suburban

1 Answer

How do I change the transmission seal on a 2002 kia sportage?


remove the drive shaft place a jack under the transmission and remove the trany mounts and bellhousing bolt any lines and linkage attached to the transmission separate tranny from engine

May 16, 2014 | 2002 Kia Sportage

1 Answer

Is thier a way to take a tranny out without dropping the frame


NO. the bottom frame must be removed, it alot of work to remove the tranny on a ford taurus, you will need a top engine support also, this will hold the engine and trany inplace to remove the frame and then you lower this to remove tranny. good day.

May 12, 2011 | 1997 Ford Taurus

1 Answer

How do i remove the transmission from a 2001 ford taurus


this is a big job,you will need to dissconnect the battery, then you will need an engine support bar to hold and lower the engine from the top. you will have to remove the battery and the bracket and also airbox, next is to raise the car and remove the wheels and then seperate the lower balljionts on both sides, remove the axle nuts and remove the axles. then remove the swaybar ends, next is to put engine support on the top of the engine and then remove the frame from under the engine and trany, before the frame can come out you will need to remove the exhaust system and also unbolt the steering rack from the steering shaft, make sure to lock wheel so it doesnt turn,remove lines from rack, when you remove the lower frame the steering rack and all the frnot end componets like the swaybar and lower control arms will come out with the frame you will need to unbolt the front and rear engine mounts, leave the trany mount bolted for now,after the frame is out you will then remove the bolt on the trany mount, this is the mount where the battery sits at the rear of the tranny, lower the engine slowly and just a bit. next is to remove the starter and flywheel covers, you will then remove the converter bolts that hold the flywheel to converter on tranny, next is to remove the tranny bbolts, make sure to leave one bolt on for now.next is to lower engine support enough so that the tranny has enough room to come out, next install tranny jack under tranny and remove last bolt holding it,then pry away from engine always checking to make sure all bolts are out and also all wire connections unhooked, like wiring harness to tranny and selector switch connector and speedometer connection, and tranny will seperate and then you slowly lower to ground, to install reverse directions. good day.

May 01, 2011 | 2001 Ford Taurus

1 Answer

Trani Filter are they in the trani it self


the filter in usually found inside the transmission by removing the tranny pan

Jan 11, 2011 | 2004 Honda Accord

1 Answer

Clutch replacment


pull the driveshaft, take the bolts out of tranny and loosen hte nuts on tha crossmember. slide the trany back far enough to get to the flywheel bolts, or remove tranny. take out the bolts holding the flywheeland remove old clutch. go to the parts store and get your new clutch and the alignment tool(makes it alot easier)when you put the new clutch in, use the alignment tool to keep the clutch in line with the splines amd toghten the flywheel back up. remove the alignment tool and put your tranny back in .

Dec 10, 2010 | 1996 Nissan King Cab

1 Answer

HOW DO I REMOVE A TRANSMISSION ON A 1993 S10 BLAZER 4X4


remove drive shafts remove cross member, and transfer case mount remove transfer case then remove tranny there are 6 bell housing bolts that hold tranny in 15 mm i think and 2 trany lines if its auto

Sep 18, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

Remove transmission from a 1996 gmc suburban


I just change the torque converter, and I forgot to mark the cooling lines that come from the radiator. upper hose is flexable and is on top of the radiotor tank. does it go to the upper fitting on the tranny . and the one is solid tranny is the lower fitting on the trany , thanks for the help,

Sep 30, 2008 | 1996 Chevrolet Suburban

1 Answer

How do i remove the tranny away from engine


i think this is what your missing.
hope it helps

f8fa58c.jpg
9a9284c.jpg
85e0fd6.jpg

Jul 15, 2008 | 2000 Mitsubishi Eclipse

3 Answers

Tranny fluid level 2005 chevy malibu sedan


its a pain in the a.. to check under the car on passager side you got the axel shaft coming out of trany beside it there a plug before removing the plug heat up engine the motor running remove the plug 7/16 kee or 11mm if you see oil comming out its full if no oil come out take a funnel remove the red cap on the top of trany use gm oil only fill untill you see it drip under the car put plug plug back and that it be carefull to lift the car and not burning our finger will removing the cap
from montreal canada thank you
pierre

Jun 23, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
1996 Chevrolet Suburban Logo

977 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...