Question about 2000 Jeep Grand Cherokee

3 Answers

2000 Jeep Grand Cherokee turn signal problems

Why would a turn signal randomly stop working?

Posted by on

  • Anonymous Dec 10, 2008

    try lifting your four way hazard button,on steering column

  • Anonymous Mar 13, 2014

    2000 Hyundai heater not working turn signal working heater fan not working



3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 5,568 Answers

The typical turn signal relay is load dependent and designed to operate erratically or faster if a lamp has failed as kind of an alert to the driver that something is amiss.
That it is intermittent likely means that you have a bulb that is sitting in a corroded socket and not making contact all of the time if it is occurring on one side. If on both sides, the relay itself is failing or its socket is corroded which is less likely since it is under the dashboard protected from the elements.       

Posted on Oct 01, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 161 Answers

This could happen from a short in the wire or it could be getting grounded out from a damaged wire also ground wire could be corroded...check and replace/repair....any questions? contact me

Posted on Oct 01, 2008


If its a rear lamp they have had aproblemb with the circuit board in the lamp assy itself may need a new lamp

Posted on Oct 01, 2008

3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 52 Answers

SOURCE: Turn signals quit working

you need a multifunction switch, not hard to replace 3 screws in the column shroud then take both shroud halves off and there it is. to get the part just take your vin to your local dealer and tell them multifunction switch

Posted on Mar 23, 2009

  • 840 Answers

SOURCE: Turn signals quit working

one of the bulbs is not working soneither ill work so you need to check both bulb check the rear first its the easiest 2 screws inside rear and pull out light

Posted on Jan 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2008 Kia Optima turn signals/brake light won't always work

This is probably a bad earth connection, Try checking the connection to the rear light cluster for corrosion around the wiring plug, remove it and clean the connections, also check the bulb fittings, clean and replace bulbs into the holder. This is normally where the problem is, and could be due to water getting into the rear lights, good to check for this too.

Aug 12, 2014 | 2008 Kia Optima

1 Answer

Left turn signal stops working

Had simular problem with wife 2000 Jeep Cherookee.
My signal light were not working at all.Check flasher relay under steering colum

Nov 28, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Left brake and turn signal lights are out on my 2000 Jeep Grand Cherokee

If they are two different bulbs, I would look for a ground wire problem.
If the two lights are the same bulb, could be a socket or turn signal switch problem.

Jul 03, 2012 | 2000 Jeep Grand Cherokee

1 Answer

I can't get my turn signal lights to work on my

check see if ur bulbs on signal lights are ok or need replace. other problem is the wire got switch with other signals or no connect. see if this help.

Apr 26, 2012 | 2000 Jeep Grand Cherokee

1 Answer

How to fix my right brake light and fast moving turn signal on my 2000 Jeep Grand Cherokee?

The most likely problem is two burned out light bulbs. A burned out tail/stop lamp on the right side and a burned out brake lamp on the left. If you have already replaced the bulbs, then yes, the circuit boards are the next most likely cause of the problem.

Apr 07, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Turn signal keeps clicking randomly Pontiac grand am 2002

This can either be caused by the hazard switch located above the radio or the turn signal /multfunction switch on the steering column.When it is doing this try wiggling the turn signal switch and see if it stops. If it does stop the issue is most likely in the turn signal switch.

Apr 20, 2011 | 2003 Chevrolet Malibu

1 Answer

My blinkers work sometimes and then stop working for a while, then will start working again for no reason, its very random. I dont know what i should do to get this fixed.

The turn signal flasher is bad. It is built into the hazard switch. Replace the hazard switch. The next time the turn signals quit turn the hazard switch on and off a few times and see if they start working.

Oct 12, 2010 | 2004 Oldsmobile Alero

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

940 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides