Question about 1996 Pontiac Grand Am

1 Answer

1994 grand am ignition switch

The ignition switch was changed one time before, and now the switch is in need of being replaced. would I need special tools to remove it and how difficult is it to remove and install.

Posted by on

1 Answer

Two bolts and a plug

Posted on Oct 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1994 Jeep Grand Cherokee with the 5.2L is very difficult to start if it has not been run in the previous 6 hours. Replaced ignition coil but didn't solve the problem. After sitting overnight it


Low fuel pressure.
You need to check the fuel pressure on the first crank and watch it as it is running.
Requires a special gauge.
If it were just a starting problem I would say it could be a pump relay, but not if it runs rough for 5 min.
Might be a dirty filter or problem in the tank.

Jun 29, 2012 | 1994 Jeep Grand Cherokee

1 Answer

1996 Jeep Cherokke 5.2 grand laredo, missing on acceleration found loose distributer need to set timing.


Base (initial) ignition timing is NOT adjustable. Do not attempt to adjust ignition timing by rotating the distributor. All ignition timing functions are controlled by the Powertrain Control Module.Adjusting the timing on a Jeep Grand Cherokee requires special tools and an understanding of engine mechanics. Changing the timing on a Jeep Grand Cherokee with distributor-less ignition requires professional reprogramming of the powertrain control module. This guide covers Jeep Grand Cherokee models with distributed ignition only. you can go to this site and it will explain it. www.ehow.com/how_4521340_adjust-timing-jeep have a good day !!

Jun 07, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Instructions to change ignition switch


do a search on www.youtube.com for "pontiac "lock cylinder" "ignition switch" you can watch somebody else do it and decide if you want to take it on. bear in mind that special anti-theft hardware is holding it in and special tools will be needed to take it apart.

May 09, 2011 | 2004 Pontiac Grand Am

1 Answer

Where is the ignition switch located on a 2000 pontiac grand am gt.


you put your ignition key into the lock cylinder. if you put the right key in, it fits and turns the ignition switch. so your ignition switch is more or less directly behind and in line with your key when it is in the lock cylinder. inside the steering column. it is not easy to get at, and you will find that special anti-theft tools are needed to replace it.

Apr 20, 2011 | 2000 Pontiac Grand Am GT

2 Answers

I tryed to start my car and the key feels like its not catching it just spins past the start. jeep grand cherokey 1994 v8


the key is just the lock assembly the actual ignition switch is behind thelock take the plastic covers off steering housing the ignition is the black square housing held on with tamperproof torx screws easy to replace

Jan 26, 2011 | 1994 Jeep Grand Cherokee

1 Answer

Service 4x4 switch what does that mean


it could simply mean change the oil, please put the key in the ignition and turn it forward not enouf to start it and then push down on the gas pedal 3 times all the way to the floor then wait 5 seconds and turn the key in the off position and then start vechile, this should reset that service light. for futher help please call 419 689 1114 and i will be happy to assist you.

Apr 24, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Can't turn the ignition 1994 pontiac sunbird 4 cylinder.


your probably going to have to replace the tumbler. you will need a special tool to remove the steering wheel .

Apr 06, 2009 | 1994 Pontiac Sunbird

Not finding what you are looking for?
1996 Pontiac Grand Am Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...