Windows driver passenger not working

Rear Passenger Power Window Operation
The rear passenger power window switches receive battery voltage through the window lockout control circuit if the window lockout function is disabled. Ground for the rear passenger power window motors is supplied through normally closed up and down contacts of both the rear passenger power window switches and the driver power window switch. When the either rear passenger power window switch is placed in the down position, the power window motor down control circuit is switched to 12 volts and is applied to the down side of the rear passenger power window motor. Since the other side of the rear passenger power motor is connected to ground through the normally closed up contacts of both the rear passenger and driver power window switches, the window travels down. By placing the rear passenger power window switch in the up position, the polarity of the power window motor is reversed and the window travels up.
The rear passenger power windows can also be controlled from the driver power window switch.

Did you try pushing the lock out switch on the drivers master switch ?

Did the switch work before replaced battery ? 2008 CTS ? Cadillac ? These switches are inputs to a control module , DDM - driver door module . a computer of sorts . A lot of thing's can go wrong with these systems , broken power or ground circuits inside the rubber boot from the body to the driver door . Communication problems between control modules etc... Plus the power windows don't use fuse's , has a circuit breaker for front windows - PWR/WNDW circuit breaker 25 amp located in the fuse box under the back seat , Fuse's are used for rear windows - two 15 amp fuse's LT/REAR an rear ,both are in the rear fuse box under back seat. These rear windows are controlled by the BCM - body control module .

The power windows system consists of the following components:
• Driver door module (DDM)--GMLAN device that receives and transmits messages and signals for window functionality. The DDM contains the driver door switch (DDS) which is integrated into the module. The DDS contains the driver, front passenger, RR and LR window and window lockout switches.
• Passenger front door module (PDM)--GMLAN device that receives and transmits messages and signals for window functionality. The PDM contains the front passenger door switch (PDS) which is integrated into the PDM. The PDS contains the front passenger window switch.
• Left rear power window switch--Provides switched voltage and ground window switch signals to the left rear window motor for left rear passenger window operation
• Right rear power window switch--Provides switched voltage and ground window switch signals to the right rear window motor for right passenger window operation
• Left front power window motor--Contains position sensors and a module that receives signals from the DDM and provides a status signal to the DDM
• Right front power window motor--Contains position sensors and a module that receives signals from the PDM and provides a status signal to the PDM
• Left rear power window motor--Contains position sensors and a module that receives signals from the left rear power window switch
• Right rear power window motor--Contains position sensors and a module that receives signals from the right rear power window switch
• DRIVER DR MOD fuse (15-amp)
• PDM fuse (15-amp)
• PWR WNDW Circuit Breaker (25-amp) -- front
• LT/REAR/WNDW fuse (15-amp) -- rear
• REAR/WNDW fuse (15-amp) -- rear


Power Window Operation
The driver and front passenger doors are equipped with power window motors that contains its own module. Each power window motor receives a hot at all times battery supply voltage and constant ground source. When the right front passenger window switch on the DDS is activated to the up or down position, the DDM will interpret the signal and send a GMLAN serial data message to the PDM. Upon receipt of the message, the PDM will send a signal to the front passenger window motor module on the GMLIN serial data circuit. The window motor module will then supply battery voltage and ground to the window motor to drive the window motor to the up or down position.
The DDM communicates via the GMLAN serial data circuit with the body control module (BCM) to control the rear window functions from the driver master window switch. The BCM is hard wired to each rear power window switch with circuits for window up, window down, and an enable circuit. The rear window switches contain internal logic that when supplied with voltage from the BCM over the enable circuit will driver the appropriate window in the direction commanded.
The rear power window switches are supplied with battery voltage from individual right and left WNDW fuses located in the rear fuse block. When a rear power window switch is activated to the DOWN position, voltage is applied to the motor down circuit and the motor up circuit serves as the path to ground. The window motor will drive in the downward direction until the switch is released or the window has fully opened. When the window switch is activated to the UP position, voltage is applied to the motor up circuit and the motor down circuit serves as the path to ground. Ground for the left rear power window switch is supplied at G200 and the right rear power window switch receives ground at G201.

The power locks work the same .

After replacing the driver door switch (DDS) or passenger door switch (PDS), perform the programing procedure.

If you don't know any of what i posted your best bet , have a qualified repair shop check it out .

seems online that the avenger has lots of window issues. Lots of places selling new window switchedes
2008 Dodge Avenger Window stuck down DodgeTalk Dodge Car Forums Dodge...


visit link for dodge forums





http://www.dodgetalk.com/forums/showthread.php?t=371049

Before you replace anything, inspect the connector pins in both the driver's door switch and the passenger door switch. If you don't find any problem with these connector pins, replace the driver's door control switch.

Look at the body control module.

This sounds like a stuck switch,try to unplug the switch (drivers side window) first and it should cure your problem.Let me know if this does it,,if not i will help you solve this issue

The motor on the passenger side is shorted and is now tripping the circuit breaker. Odds are, the back window motor is also bad. You have to take the panel off to check the motor. You can power it directly to verify it has failed.

The last couple of times I have seen this complaint, the "Lock" button on the master (driver's door) switch had been depressed. Unlatching the lock button (pushing it again) solved the problem. On most cars, when the lock button is depressed, the windows can still be operated by the driver, but prevent the windows from being operated by the passengers. Toyota is different. If the lock button is depressed, nobody, including the driver can work the wndows.

the window motors are most likely no good