Question about 1995 Jeep Grand Cherokee

1 Answer

How do I replace the pcm on 95 jeep larado??? thanks!!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Hi there:
I have the same Jeep GC Limited...

how do I replace the pcm on 95 jeep larado??? - 12_14_2011_2_02_05_pm.jpg

Fig. 1: Powertrain Control Module (PCM) location

According with this specific section from Jeep Repair Manual, check this procedure to removal and installation:

  1. Disconnect the negative battery cable.
  2. Remove the coolant reserve tank and disengage the three electrical connectors from the PCM.
  3. Remove the three PCM mounting bolts and carefully remove the PCM.
  4. Installation is the reverse of removal.

If ypou need additional details, just contact us in the previous link. Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Posted on Dec 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my alternator dont charge at normal engine idle thanks


You have rvc/regulated voltage control, that circuitry is in your pcm. I'm not saying the pcm is faulty, at the moment, I don't know? You also have a battery temp sensor in the battery tray housing, that might cause problems?
Check for applicable charging system trouble codes, if you haven't already.

Mar 30, 2017 | Jeep Cars & Trucks

1 Answer

Where is the TCM located on a 2997 Jeep Grand Cherokee Larado, 4 liter, 4 wheel drive


2997, my cystable ball is too fogging out 900 years,
my guess, is there gas pumps are long ago dry....
we walk now.
most cars the TCM is now in the pCM.
just about that year for most cars. (integrated now)
if posted the manual now 10000 times.
guess 1. ZJ jeeps
8w31-1
and there IS NO TCM
just TCC locker.




25969931-mgmuftjmuwumvfkqzzfa3nwy-3-0.jpg why not post symptoms first. then we can easter egg hunt all day.

Nov 20, 2015 | Jeep Cars & Trucks

1 Answer

How to remove a dashboard from a 1994 grand cherokee


XJ 94
its not bad, wana bet? 90% are not.
(i used to fix them)
so the PCM,. the FSM book covers that.
why not read that.
JEEPJX
PCM is baD ONLY WHEN inputs good, and its outputs are bad.
(and outputs not shorted) !!!
(same or all computers on earth)
lose of power to PCM or ground
or bad power.(weak, or intermittent)


Got DTC errors , post them?
innova 3140 best bank for buck on 93-95 jeeps. !!!
that is a low priced scan tool

are you having ASD relay issues?
http://www.fixkick.com/Jeeps/ASD.html


see XJ 95 here (same i think)
http://colorado4wheel.com/manuals/Jeep/XJ/

page 8D-23
engine bay next to Air cleaner.

to diagnose any car, a real scan tool is best.
or you will need a full lab of meters and scopes. like me.
the scan tool show up things the keyon/off trick does not.
http://www.fixkick.com/Jeeps/jeeps.html#poor_mans-scan


25499888-tk5pw0guzkbs2wb12fwiwrb2-5-0.jpg

Mar 01, 2015 | 1994 Jeep Grand Cherokee

1 Answer

We have a 95 Jeep Grand Cherokee Larado. It was


Your starter does not actually start your car. It's only job is to turn the engine so it can start. (actually replaces the crank people used to need to put into the front of the car and physically crank (turn) the engine...hence the term "cranking")
The two most common causes of the problem you are having is either the crank position sensor or fuel pump has failed. Easy way to determine if the pump is bad is to listen to the gas tank when you turn the key to the "on" position...You should be able to hear it. CPS needs to be checked with a digital ohmmeter Best instructions for electrical testing can be found in chilton manuals available in most large parts stores. Haynes is somewhat useful but a bit too basic for any real electrical diagnosis. All sensors are expensive (min of $90 each) so testing is important so you don't end up throwing $ at it with no results.
Need answers to anything you find just ask!!.

May 21, 2010 | 1995 Jeep Grand Cherokee

1 Answer

I have a 95 Grand Cherokee Larado.I have a binding noise coming from the front end. Just replaced, bearings and U Joints in front, and seals and bearings in back.


sounds like the drive shafts may not be right back properly or maybe a u joint not seated in straight
jack the truck up and spin whel by hand with 4 wheel locked and look for the binding noise

Apr 14, 2010 | 1995 Jeep Grand Cherokee

2 Answers

1995 Jeep Larado-alarm wont turn off


hi have u tried taking wires off battery then eathing then for a minute and putting back on

Jul 29, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

83951 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...