Question about 1996 Honda Accord

1 Answer

96 honda accord Removing brake rotor

How do I get the brake rotor off once the 4 bolts on the hub are removed???

Posted by on

  • Anonymous Apr 11, 2009

    i cant take off the rotor because it seems lyk i have to take off the hub but im not sure so i wanna ask enebody

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

Hi remove the the rotors retaining screws then remove the two bolts holding the caliper and pull it out of the way take the rotor off yates210456

Posted on Oct 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to take front rotor off. How do I do it


the front rotor bolts on the drive hubs with 4 bolts or screws depending on the setup. once you remove the brake caliper then you can remove the bolts that retain the caipier mounting bracket (normal two bolts on the back side 17 or 18 mm scoket) then you can remove the rotor bolts and the rotor. i hope this helps

Feb 26, 2011 | 1992 Honda Accord

1 Answer

Changing front brake rotor on 1995 honda passport


Put the parking brake On and jack up the front of your SUV.

Remove the lug nuts and you will be able to remove the tire and rimm by sliding them off.Remove the spindle bolt located at the center of the rotor using an 36 mm socket(approx).

Remove the two nuts located behind the rotor (one at top and other at the bottom). This will enable you to remove the brake caliper.While removing it be careful that the caliper tube stays straight.

Slide under your passport and remove the 4 bolts behind the hub using an 12 mm(approx) wrench.Pull the hub assembly out and this will remove the hub rotor in some cases if you are using an tool for pulling the hub assembly out or you have to slide the rotor off the hub assembly.

Slide the new rotor into the hub assembly.Reinstall the brake caliper and make sure the caliper tube is not twisted. Replace the spindle bolt.

Nov 14, 2010 | 1994 Honda Passport

1 Answer

1991 Honda Accord had the brakes change new rotors and pads. Drove 50 miles and the front drive axle where it goes into the front wheel looks and acts like it is stripped out. It's making bad noise if you...


Brake Disc (Rotor) REMOVAL & INSTALLATION 1990-95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the steering knuckle from the vehicle. Please refer to Section 8 for procedures.
  5. Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit. Fig. 4: Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit/rotor assembly 86809032.gif

  6. Remove the 4 bolts, then separate the hub unit from the brake rotor. Fig. 5: Remove the 4 bolts, then separate the hub unit from the brake rotor 86809033.gif
    To install:
  7. Assemble the disc to the hub unit and tighten the bolts to 40 ft. lbs. (55 Nm).
  8. When installing the hub to the knuckle, use new self-locking bolts and tighten them to 33 ft. lbs. (45 Nm).
  9. Install the steering knuckle.
  10. Lower the vehicle and check for proper brake operation.
  11. If equipped, enable the SRS system and connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1991 Honda Accord

1 Answer

How do you the rotor off a 1990 honda accord lx


REMOVAL & INSTALLATION Except 1990–95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the two 6mm screws from the brake disc. Fig. 1: Remove the two 6mm screws securing the brake disc 86809029.jpg

  5. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  6. Remove the caliper bracket. Fig. 2: Remove the bolt and guide pin from the caliper bracket, then remove the bracket 86809030.jpg

  7. Remove the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly and alternately to prevent cocking the rotor. Fig. 3: Remove the brake disc from the caliper assembly 86809031.jpg

  8. Installation is the reverse of the removal procedure.
  9. If equipped, enable the SRS system and connect the negative battery cable.
1990–95 Accord
  1. If equipped with an air bag, disconnect the negative battery cable and properly disable the Supplemental Restraint System (SRS), as detailed in Section 6 of this manual.
  2. Loosen the lug nuts, then Raise and safely support the vehicle on jackstands.
  3. Remove the wheels.
  4. Remove the steering knuckle from the vehicle. Please refer to Section 8 for procedures.
  5. Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit. Fig. 4: Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit/rotor assembly 86809032.gif

  6. Remove the 4 bolts, then separate the hub unit from the brake rotor. Fig. 5: Remove the 4 bolts, then separate the hub unit from the brake rotor 86809033.gif
    To install:
  7. Assemble the disc to the hub unit and tighten the bolts to 40 ft. lbs. (55 Nm).
  8. When installing the hub to the knuckle, use new self-locking bolts and tighten them to 33 ft. lbs. (45 Nm).
  9. Install the steering knuckle.
  10. Lower the vehicle and check for proper brake operation.
  11. If equipped, enable the SRS system and connect the negative battery cable.
prev.gif next.gif

Aug 21, 2010 | 1990 Honda Accord

1 Answer

How do you remove the rotors from a 1991 honda accord?


Loosen both front wheel lug nuts and raise car and support on jack stands. Remove wheels and have a friend hold brake pedal down and remove axle nut. Use a chisel or screwdriver to remove stake on nut to axle edge. I use a 3/4 drive set socket and remove axle nut. Rent it from Autozone. Remove caliper assy and support with coat hanger or bungee cord to hold weight of assy off of brake hose. Remove Cotter pin and nut on lower control arm. Separate with ball joint fork and pull strut assy away to the side while pulling stub axle through and out of the way. Remove 4 bolts holding rotor and hub assy. on the inside of steering knuckle and separate. Now remove 4 bolts on hub's outer side and separate rotor and hub. You can use a bar or large screwdriver between wheel studs to loosen the 4 bolts.

Aug 04, 2010 | 1991 Honda Accord

1 Answer

I need to know how to take out the front rotors coz everytime i brake, my steering wheels shaking


ON THE 95 AND 96 ACCORD THE ROTORS WERE BOLTED TO HUB. ITS A JOB! U NEED A HUB REMOVER,AXLE NUT SOCKET AND METRIC TOOLS. IF U NEED STEP BY STEP I CAN CLARIFY. IT TAKES ABOUT 2-3 HOURS A SIDE DEPENDING ON HOW EXPERIENCED U ARE

Aug 04, 2010 | 1996 Honda Accord

1 Answer

How to remove front discs on 1991 honda accord


Loosen the lug nuts, then Raise and safely support the vehicle on jack stands.

Remove the wheels

Remove the steering knuckle from the vehicle.

Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit.

Remove the 4 bolts retaining the hub unit to the steering knuckle and remove the hub unit/rotor assembly

Remove the 4 bolts, then separate the hub unit from the brake rotor
6e199b7.jpg

To install:
1. Assemble the disc to the hub unit and tighten the bolts to 40 ft. lbs. (55 Nm).
2. Install the steering knuckle.
3. Lower the vehicle and check for proper brake operation.

Jun 15, 2010 | 1991 Honda Accord

3 Answers

Resurfacing front rotors


This tutorial will help you : http://www.ehow.com/how_4719219_off-brake-rotors.html
Some after market brake pads are better than the company fitted ones, but they will be more costly.

Jun 01, 2010 | 2004 Honda Accord

2 Answers

How do you replace the front rotors on a 1996 honda accord?


Remove wheel. Take off outer driveshaft nut. Remove lower ball joint pinch bolt & separate ball joint from spindle. Pull rotor & spindle out & away to pull driveshaft outer splined end out of rotor center hub. Look on the back of the spindle for the 4 bolts that hold in the wheel bearing. Use a 12 point socket to remove the 4 bolts and remove wheel bearing from spindle (out towards the wheel stud side). Probably will have to use a air chisel to get it out. Once it's out undo the 4 bolts on the outer (wheel stud side) of the rotor and remove the rotor from the hub. Clean & lube the hole where the bearing was in the spindle & the inner face of the hub. MAKE SURE IT'S CLEAN otherwise you may get a pulsation on braking if theres a piece of rust or dirt between the rotor center & the hub face. Reverse procedure to install.

If the rear bolts don't come out then you will have to use a slide hammer to separate the bearing to replace the rotor and there is a very good chance you will need to replace the wheel bearing after you're done (noisy on road test).


Not the job to do at home, usually an easy 2-3 hours per side if things go bad (book time is 2.2 hrs per side). Use good quality rotors as you don't want to have to do it again because a cheap rotor gave you a pulsation.

May 28, 2010 | 1996 Honda Accord

1 Answer

93 honda accord rotors


Your Accord has what is called "Trapped Rotors". They actually fit behind the hub. The procedure to remove them is not complicated, but it is time consuming.
Here is how I do it:
1) Remove axle retaining nut.
2) Remove brake caliper and bracket.
3) Remove lower ball joint retaining nut and use pickle fork to loosen spindle from lower ball joint.
4) Remove axle from hub.
5) On the back of the spindle, remove four bolts that attach hub/bearing to spindle.
6) Use slide hammer to remove rotor/hub assembly.
7) Remove 4 bolts attaching rotor to hub.
8) While it is a snug fit, the hub bearing does slide through center of rotor to remove it.
Installation is in reverse order.
A bad bearing usually makes a growling noise while driving.

Jun 06, 2008 | 1993 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

722 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...