Question about 2004 Toyota RAV4

1 Answer

Instalation for lights

I need the circuit guide to insalling the fog lights on a rav4 2004! if you could email it to bonnieobrien_88@hotmail.com asap.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

There will be plugs already there on the main light harnes to plug in the fog lights. the harness runs along the bottom of the radiator . this should help you... please rate

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which relay is the correct relay for dash lights and fog lights


I'm just now seeing your question at 3pm est so I don't know when you first posted it.
Your car has several different wiring systems for the lights so you may have to get a book to figure it all out.
There is a fog light relay, but it has nothing to do with the rest of the lights, unless your car also has an isolation relay. The isolation relay grounds the fog lamp relay on some models.
There may also be an instrument cluster microprocessor if the car has automatic light controls or daytime running lights.
Its possible you popped something in the headlight switch too.
I would get a book with the diagrams and start at the fog lamp and dash light fuses then go from there. See if the fuses have voltage first.
Some of the diagrams can be found online, such as at autozone's website under repair help.

Aug 08, 2012 | Cars & Trucks

1 Answer

I just bought a 2009 dodge ram without fog lights i bought a bumper with fog light an switch them out but i need to know how to connect the lights to the factory switch inside what do i need to do


If your PU didn't come with factory installed fog lights then you will need to replace your headlight switch with a fog light enabled headlight switch.

Here is a link to the factory dealer-installed instructions.....

http://www.mopardodge.com/accessories/Instructions/82208102AC_IFU.pdf

You only need to get the components you don't already have. The headlight switch that is fog enabled will pull out for fog light operation, if yous doesn't you need to replace the switch and do some wiring as shown in the pdf file linked above.

Hope this helps!

Mike

Apr 18, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Wiring of fog lights on 95 Mustang


If you bought the fog lights from Ford and they plugged into factory plugs at the front bumper, then I suspect you need the headlight switch that came optional for your car. You will need to install a relay into the fuse box. Check for any fuses for that circuit. I did one on a Ford f-150 and the switch came with the lights from Ford.Usually the fog lights are not on until you push a button or turn the switch.

Mar 15, 2009 | 1995 Ford Mustang

2 Answers

I need a wiring diagram for fog lights oem to my toyota


The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

1. You can cut them off (in other words, there must be a switch installed to turn them off)

and

2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

http://www.accessconnect.com/fog_driving_lights_wiring.htm

Feb 28, 2009 | 2005 Toyota Corolla

2 Answers

2001 olds aurora keeps overheating!!


My car keeps on overheating only on the highway when i reach bout 65 or 70 mph. it does fine all around town i can drive the thing all day around town non-stop, but when i hit the open road it gets hot tells me. hot turn ac off let engine idle...anyone knows the question to that let me know via email treybird_loves_basketball@hotmail.com i would really appreciate the advise or someone who knows what hell prob is.. preciate it...

Dec 30, 2008 | 2001 Oldsmobile Aurora

1 Answer

No fog lights on 92 talon non turbo, FWD


Yes you can have fog lights. You will need to buy the Haynes Manual and it will show you where to attach the wires underneath the harness under the hood. The easist way to do this is the biggy back the fog lights onto the main running lights circuit. NOT THE HEAD LIGHTS CIRCUIT. That way when you turn on the running lights the fog lights come on automatically and the fuse is strong enough to power both, and you could bump up the fuse about 10-15amps, but no more.

Hope that helps!

Thanks,

Mark

Dec 05, 2008 | 1992 Eagle Talon

1 Answer

Installing after market fog lights


look where they mount the lights connectors are probably right there

Nov 01, 2008 | 1999 Jeep Wrangler

1 Answer

2001 acura hid fog lights


h3 hid kit will fit in there. email: enam285@yahoo.com

Jun 21, 2008 | 2001 Acura 3.2CL

Not finding what you are looking for?
2004 Toyota RAV4 Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...