Question about Mitsubishi Colt

1 Answer

92 colt 100 hesitates at low speed but runs fine after it speeds up.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Maybe clean the fuel system, like the injectors and stuff, or maybe it needs a new air filter. I am assuming it is fuel injected, since it is a 92. or, maybe it needs something in the ignition system.

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 crown vic lx ... I changed the wiper motor, switch and the power train Control module. Still don't have wipers!! Any suggestiobs??? Thank you!




1. Access the interval governor located above the warning chime
under the driver side of the dash and disconnect it.

2. Install a jumper wire between the Dark Green (DG) wire and the Yellow/Red (Y/R) wire.

3. Install a 2nd jumper wire between the Dark Blue/Orange (DB/O) wire and a Black (BK) wire. Either BK wire of the module should work, both are dedicated chassis grounds for the module.

4. Turn the ignition switch to the Run position and verify that the wipers are running on low speed.

5. Disconnect the jumper wires.

6. Connect an ohmmeter between the Dark Blue/White (DB/W) wire and the Brown/White (BR/W) wire.
With the wiper switch in the OFF position, resistance should indicate about 47,500 ohms.

7. Move the wiper switch to the low speed position, resistance should change to indicate about 4000 ohms.

8. Move the switch to the high speed position, resistance should change to indicate less than 100 ohms.

9. If the wiper motor runs and the switch resistance checks as stated, replace the interval governor.

May 31, 2015 | Cars & Trucks

1 Answer

2004 Ford expedition has started to hesitate at low speed (20to35).starts and idles fine and runs better at higher speed..


One or more of your cips(coil in plugs) have gone bad. Go have your code check read at autozone. It should tell you which cip is bad

May 02, 2015 | Ford Cars & Trucks

1 Answer

My Colt's engine heat increasing drastically when driving in slow speed/stucked in traffic jams...


Overheating at low speeds is an indication of coolant flow problem or air flow problems, check you radiator fan, fan relay and coolant level.If you need more help on fixing cooling fan I would suggest you to check out the below site HowTo section http://www.buyautoparts.com/howto/

Oct 14, 2013 | 2006 Mitsubishi Colt

1 Answer

Why does my blower motor wotk on all speeds except high on a 92 s10


you need a blower resister most likely. or the speed control switch. 99 out of a 100 times the resister shot craps

Jul 12, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

Engine misses/hesitates on low speeds. Runs fine


is the check engine light on? have you ever serviced the injectors? if not try that first because there are many things that give the symptoms you spoke of. but this is the cheapest.
vbninja E.A.P

Jul 23, 2010 | 2005 Cadillac CTS

1 Answer

At 40 klm per hr i get hesitation and at 80 if i hold steady. at 100 it runs great. no problem with hesitation if i take it up to 100 qiuckly. only if you hold it steady at lower speeds


Have the voltage checked on the TPS. If it has an open circuit which is very possible at all areas of the internal reostat it will make the vehicle run such as yours does now

Apr 28, 2010 | 1996 Dodge Caravan

3 Answers

Bmw 3.0 x5 hesitation problems


sound like throttle position sensor.have it check out.also check air duct connected to mass air flow sensor and throttle body.if air duct is loose or off.it will cause severe hesitation.

Jul 21, 2009 | 2009 BMW X5

1 Answer

92 dodge colt sedan


hey
in most cases the reason it's of two things. either your catalytic converter is plugged or you are losing fuel either from a plugged filter or a bad fuel pump. wouldn't be a bad idea to check the air filter also.

Jul 10, 2008 | 1992 Dodge Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...