Question about 1991 Jeep Cherokee Briarwood

1 Answer

1991 jeep cherokee sport 4.0

It has 151252 km on the motor,I had to replace the head gasket,what is the head torqued at?

Posted by on

  • Anonymous Dec 12, 2008

    head bolt torque

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

 For your 1991 Jeep Cherokee 2WD 4.0L MFI :
  Foot pounds (Final torque) 

  Note:
  Torque sequence ------------------  
  front    | 12  8   4   1   5   9  13 | 
  of | | 
  engine | 11  7   3   2   6   10 14 | 
  ------------------  
Final torque must be reached in 3 equal steps  
  Step 1: torque all bolts (except bolt 11)  
  to 110 Ft/Lbs  
  Step 2: torque bolt 11 to 100 Ft/Lbs  
Recheck final torque in sequence  

Posted on Sep 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 jeep Cherokee keeps over heating


Several possibilities, including blockage in coolant tubes of radiator, damaged or slipping impeller on water pump, blockage of air flow through radiator, inoperative radiator fan(s), damaged head or head gasket...

Does the radiator fan come on? If not, problem could be bad temp sensor or fan motor or wiring.

Mar 26, 2016 | 2008 Jeep Cherokee Sport

1 Answer

99 jeep Cherokee... replace head gasket still pushing water out of radiator any suggestions... also can anyone give us the specs for torqueing the head


if its the 6 pot in line engine then its a cast head and the torque will be around 75lbs ,if its pushing water then iam afraid the head will need further examination like its warped or the water ports have opened up due to corrosion where its had no antifreeze .Or you have damaged the gasket putting the head on and open up to it as we have all done even the best of mechanics

Aug 16, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

HOW TO FIX A BLOWN HEAD GASKIT?


Buy a gasket kit for the upper end. Remove the valve cover intake and exhaust manifolds. Remove the head bolts. Remove head and clean up block from old gasket material. Take the head to a machinist and make sure that it is not warped. If it is warped either replace the head with a new one or have it machined true. Install new gasket and get torque specs with new head bolts and follow torque sequence using the correct torque specs. Clean exhaust, intake and valve cover of old gaskets. install new gaskets and torque according to specifications.

Nov 27, 2010 | 1993 Jeep Cherokee Country

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

1 Answer

I have a 1991 jeep cherokee sport with a 4.0 high output engine i put a new radarator new head gasket new head new water pump and new cluch fan also new therostate i can,t get the therostat housing to seal...


try aviation gasket maker / messy but stops leaks .make sure you have all surfaces clean no debris stuck on them and the right thermostat that fits and the proper gaskets or o ring and a little avaition gasket glue should cure the problem . leaks require patience :) gl

Jan 06, 2009 | 1993 Jeep Cherokee Country

1 Answer

Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L


the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Jan 04, 2009 | 2004 Jeep Grand Cherokee

1 Answer

I need repair instructions for changing the head gasket on 2000 Jeep Cherokee Sport


your best bet would be to go to a local parts store and purchase a Haynes manual for your specific vehicle, this will give you step by step instructions as well as all the required torque specs. The Haynes manuals are around $ 25.00 canadian. hope this helps you.

Oct 08, 2008 | 2000 Jeep Cherokee

1 Answer

Jeep overheating


your head gasket is gone....this will require a new gasket and the head to be skimmed.....dont be wasting money on anthin else

Aug 28, 2008 | 1991 Jeep Cherokee Limited

1 Answer

Headgasket repair tools


10mm 13mm "12mm 12 point sockets on head bolts and a torque wrench" screw driver and plires
should be just about it

Jun 25, 2008 | 2000 Chrysler Grand Voyager

Not finding what you are looking for?
1991 Jeep Cherokee Briarwood Logo

411 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...