Question about 2004 Hyundai Elantra

1 Answer

Camshaft postioning sensor

I was told that my camshaft positioning sensor was bad and needed to be replaced where is that located on a 2004 hyundia elantra 2004

Posted by on

  • Deb101 Dec 13, 2008

    I have the same problem apparently-per autozone. My check engine light is on and the car jerks when I accelerate-need help soon.

  • phydeauxshax Feb 06, 2009

    I had camshaft positioning sensor and fuel filter replaced...still having same problem. Mine is a 2000 though.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 60,769 Answers

On 1995 and later models the CKP is located at the rear of the engine near the transaxle bell housing.

Posted on Sep 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WEAR IS THE CAMSHAFT POSTION SENSOR ON A 2005 HYUNDIA SONATA V6 2.7L


It is buried under fuel hoses and vacuum lines follow top radiator hose to engine under fuel line between air cleaner box and head

Apr 23, 2012 | 2000 Hyundai Sonata

2 Answers

How do i replace the camshaft position sensor on a 2004 infiniti i35


hi, i have infinity fx 35 2003 it light on the service engine camshaft position sensor bank 1 , i replaced the bank 1 after 3 hour it light on again service engine + VDC off and slip i put the scanner it told me camshaft position sensor bank 1 again what can i do ?

Jul 24, 2010 | 2004 Infiniti I35

1 Answer

Need to know where the camshaft position sensor is located on my 2004 Hyundia Elantra


if you stand on the passengerside looking at motor the sensor is located to the left of the timing belt cover near the top of the motor.hope this helps.

Jan 04, 2010 | 2004 Hyundai Elantra

4 Answers

Where is the camshaft position sensor located on a 2004 dodge stratus 4 cyl 2.4L engine


the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Jul 08, 2009 | 2004 Dodge Stratus

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Location of the camshaft position sensor in a 2004 mercury sable


it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

May 01, 2009 | Mercury Sable Cars & Trucks

1 Answer

Camshaft postion sensor on bank 2


Should just be a simple remove and replace. Engine off disconnect sensor, remove sensor, install new and good to go (assuming the sensor is the problem to what ever issue you were having).

Apr 02, 2009 | 2004 Nissan Maxima

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

1 Answer

Car starts 1st few times ,and then refuses to start


hi
there isn't any sensor have a name ( ignition position sensor )
there is:-
crankshaft position sensor
camshaft position sensor
throttle position sensor

but there is ( ignition sensor ) locate in engine room beside the
ignition coil it was send the ignition coil signal
feedback to the (ECU)

re ask for any information

WITH MY BEST WISHES

Jul 04, 2008 | 1998 Hyundai Elantra

Not finding what you are looking for?
2004 Hyundai Elantra Logo

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...