Question about 1996 Chevrolet Camaro

1 Answer

Which way does the top go on??

I'm not sure that the people who put my top on did it correctly....there are two parts to the top I just got. The peice that has the plastic glass on it is either backwards or the big piece that covers my roof is backwards but I dont know. There is a rough side and then a soft side....which goes on the outside?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

The top on the outside should look like fabric and should look like same material all over

if you got an aftermarket top it may be different

Posted on Sep 30, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2008 Suzuki xl7 is running hot and my heater is cold air what could it be I just had a belt tensior put on

Check all the fluids and if they are low you'll need to be top off them with the correct ones make sure to ask the parts store and make sure they have them.

Nov 03, 2015 | Suzuki Cars & Trucks

1 Answer

I replaced the head gaskets on my 2001 Pontiac aztek 3400. Put everything back together went to fire it up and it turns over but will not start. Plug wires are in correct order and there is spark. Is there...

Pull the spark plugs not the wires but the plugs themself make sure they are gapped right to your car and they are not wet in any way you might be getting spark but if they are wet you mise well forget it and just buy new plugs they are like 2 dollars a peice

Sep 24, 2014 | 2001 Pontiac Aztek

1 Answer

How to change camshaft position sensor in a plymouth voyager 3.0L

It's on your transmission bell housing, remove your air box top part along with the intake hoses, the reach through to your bell housing. Should be the only thing with an electrical connection. 10mm socket is all u need and screwdriver for the air box intake tubes. When putting it in gently slide it in till it's touches the flex plate, make sure the cardboard spacer is on the new crankshaft sensor. Then tighten losely. Don't over tighten cause u may crack or brake the plastic. Then reinstall all the the peices. And your done 30min tops.

Jan 02, 2012 | 1996 Plymouth Voyager

1 Answer

Rear Window

Try a salvage yard for the part you need

Mar 12, 2010 | 1997 Chevrolet K1500

1 Answer

My liftgsate wont open on 95 jeep

take the inside panel off caerfuly and make sure all the parts move correctly. if it does then maybe you need to apply oil or grease to the parts that you think are best. if a peice is bent or broken like my brothers you just carefully bend it back or replace it.
{ I promote safety and eye protection-where your Safety Glasses! }
~ Dan Herzberg~

Mar 04, 2010 | 1995 Jeep Grand Cherokee

3 Answers

Just bought rear hatch shocks but they wont compress so that i can bolt them on

push them into a hard surface to re-compress them have a peice of wire handy and this with some muscle on your part help you get the job done

Feb 19, 2010 | 1995 Jeep Grand Cherokee

1 Answer

What size are the fuel lines going into the fuel filter. Need to know to buy the correct removal tool.

It doesn't matter just go to the parts store and ask them for a fuel line separate kit it will come with about 10 small plastic peices for about $5.00 bucks.

Jan 22, 2010 | 2004 Ford Ranger

4 Answers

I installed one piece axles, now the rear bearings run very hot... about 220 degree

Just a thought but did you check the brakes are'nt holding a bit. As I said only a thought but worth checking. Hope this help's Cheer's

Aug 14, 2009 | 1986 Jeep CJ7

1 Answer

The water pump on my eclipse froze and broke the timing belt. i replaced both parts and the car started just fine but i can feel a little shaking on the engine. i have replace spark plug and wires, the...

lt sounds very much like you have bent a valve stem. There is a quick way to check the probability of this, firstly get a peice of wood, about 50mm x 50mm and about 6oomm long (or 2x2 and2ft long in old money) With the engine idleing place one end of the peice of wood on the top of the cam cover, (thats where you put the oil in) and the other placed against your ear. you will be able to hear the valves rattle if they are bent, and sorry mate, if thats the case, it's an engine head rebuild or replace with either a new block or one from the wreking yard.

Jul 17, 2009 | 1999 Mitsubishi Eclipse

1 Answer


Yes, that is correct. What probably happened is the bulb for the check engine light burned out. The way to fix it is to pull the gauge cluster out and replace the bulb. It's not very hard to do either. If i remember right, for that year civic there are two screws holding the cluster trim in on the top inside by the cluster case. Then the dash peice connected to that that goes around the steering wheel just pops out and u just unplug the electrical switches and pull that whole peice out. Once that's out there should be 3 screws holding the cluster in, take those out and the cluster will pull right out. Carefully unplug the harness and speedometer cable and locate the check engine light bulb and twist a quarter turn and pull straight out. Then just replace with new bulb and reinstall the parts. If u can do it yourself you'll save a lot of money. A dealer would probably charge u an hour of labor which is somewhere around $115 depending on the dealer and location. Then the price of the bulb, probably a few bucks. Hope this helps, good luck!

Nov 10, 2008 | 1994 Honda Civic

Not finding what you are looking for?
1996 Chevrolet Camaro Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides