Question about 1990 Mitsubishi Minivan

1 Answer

In my L300 (van) I have almost no pressure to rear brakes. Have replaced master cylinder, apportioning valves, brake cylinders, shoes... lines look fine. Bled them to death. Can't understand whats going on... Any ideas?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Load sensing valve link between rear axle and body is out of adjustment. best way to fix is adjust in direction of downward body movement causes valve to open more. a 12mm spanner is all you need.

Posted on Oct 10, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 23 t bucket and i cant get a brake pedal.when i bought it had very little brake so i replaced rear shoes and cylinders,front pads and calipers,all new lines and the master cylinder

Once you have bled the air from the brake lines,clamp off the front brake hoses carefully.Does the pedal feel better now?
Then the pad /caliper fit is allowing too much play.Is the pedal the same?Then clamp the rear hose and try the pedal.Is it fine with the rear hose clamped?If so we now know the problem is at the rear brakes.One common low pedal rear brake cause is brake shoes that do not fit the drums.Remove the drums and look at the shoes,are they showing contact wear fully or just in the middle of the shoe?Remove a shoe and place it in the drum.Can you rock the shoe against the drum surface?Once drums have been resurfaced,the shoes will not fit fully against the drum allowing the shoe the flex when applying pressure to it and this can easily create a low soft brake pedal. Of course rear brake adjustment must be correct once brake shoe contact is correct.To correct brake shoe contact,have your shoes re arc-ed to fit resurfaced drums or install new drums.Don't overlook brake master cyl /brake pedal push rod adjustment too.

Jun 24, 2017 | Cars & Trucks

2 Answers

2007 Gmc W4500 can someone help me figure out why I cant keep brake pressure?

If you are loosing prime in the system but not loosing fluid my best guess would be the master cylinder.

Feb 17, 2016 | Cars & Trucks

2 Answers

Jeep Cherokee non abs brakes lockup!

if you have drum brake in the back most likely the shoes have cracks,replace the brake shoes,adjust parking brake you should be ok,good luck.

Jan 26, 2015 | Jeep Cars & Trucks

2 Answers

Replaced some brake line, rear pads and one rear wheel cylinder. Now no pressure and nothing happening when trying to bleed.

Does the car have ABS ? And does it have an equalizer block for the 4 wheels ?
It sounds like the ABS has been affected, or there is an equalizer block that is stuck on the front wheels only.
Can you open the bleeder or the rear line on the master cyl and get fluid to come out by depressing the pedal ?

Jul 07, 2013 | 1997 Mercury Tracer

1 Answer

1999 corolla, brake pedal goes to the floor. how can we fix the brakes?

is the abs light on?the abs system only effects the pedal when you are stopping quickly to activate the system. you still have a hydrualic brake pressure problem. are the rear brakes shoes or pads? rear shoes out of adjustment can cause a low brake pedal.even though the master cylinder has been replaced doesn't mean you got a good part.if the part was a remanufactered part very likely it is bad. to determine if it is the master cylinder, plug off the lines from the side off the master cylinder and hit the brake pedal. if the pedal stays up look for a problem elsewhere in the system. if the pedal drops the the master cylinder is defective.

Jun 11, 2012 | Toyota Corolla Cars & Trucks

1 Answer

Bleeding the brakes ,But no fluide in the rear brakes

Check the master cylinder, pump up the brakes and crack the line at the master cylinder to the rear brakes, if no pressure and it was ran empty or is new part, bench bleed the master cylinder and recheck for pressure at the master cylinder, if you have pressure follow the brake line to the proportioning valve and crack that line before and after the fitting, good luck.

May 09, 2011 | Suzuki Sidekick Cars & Trucks

1 Answer

How to trouble shoot the brake system?

To trouble shoot the brake system you have to check:AntiLock Brake System ABS:
Hydraulic Modulator
Basically this unit holds steady or bleeds off pressure in brake line, as necessary, when the Electronic Brake Control Module (EBCM) detects an abnormal deceleration in the speed of the wheel. On 2000 and later models the EBCM and Brake Pressure Modulator Valve (BPMV) are mounted on a bracket attached on the left strut tower.
Wheel Speed Sensors, brake fluid level, brake hoses and lines, inspect and replacement, Brake hydraulic system-bleeding, Brake light switch, check, adjustment and replacement.
Disk brake caliper, disk brake pads, drum brake shoes, master cylinder, master cylinder reservoir, O-rings replacement, parking brake adjustment, parking brake cables inspect and replacement, parking brake shoes-replacement, power brake booster, check or replacement, wheel cylinder inspect and replace.

Oct 10, 2010 | 2000 Chevrolet Venture

2 Answers

How to bleed the brakes on a1999 chevrolet venture van instaslled new brake pads on front tired to bleed brake pedal all the way up when van not running - goes to floor when van is running

Start with brake in the rear that is the farthest away from the master cylinder ( if your master cylinder is on drivers side start with passenger rear,pump up brake pedal until hard have someone else open bleeder valve until air or fluid squirts out,while holding brake pressure even if goes to the floor dont release pedal until bleeder valve is tightened or you will **** air back into the line,do this several times making sure you get a full stream of brake fluid and no air,continue to other rear wheel and then proceed to front wheel furthest from master cylinderand then final wheel. if you still don't have brakes change master cylinder and bleed all brakes again.

Jul 05, 2010 | 2000 Chevrolet Venture

2 Answers

Rear brakes wont apply consistantly

1- brake system low on fluid,
2- improperly bled (air in lines).
3- Master cylinder (applies equal pressure to all 4 cylinders) is bad.

Jan 08, 2009 | 1992 Chevrolet S-10

Not finding what you are looking for?
1990 Mitsubishi Minivan Logo

343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8832 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides