Question about Chevrolet Monte Carlo

1 Answer

1997 MonteCarlo None of my side marker lights work. What could be wrong?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 84 Answers

Usually caused by water getting in and corroiding the commectors
Use a phillips take em off and look sockets are cheap to replace or you can clean em

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why would only one out of 4 marker lights work?


you are right all marker lights come off of one fuse, inside instrument panel, number 29, a 10 amp fuse my manual does not give a lamp number, it has a chart, head lamps (high) lamp 9005 60 w type a, headlamp (low) 9006 51 w type b, front marker lamps 5w type d, for the rear it says to use a lamp 7443 21.5 w type d, I do not use these, I have special lights on mine, hope that it helps

Mar 28, 2015 | 2007 Scion tC

2 Answers

Front side marker / turn signal wiring diagram for 1997 crown vic LX. Both directionals works, but parking light on driver side dosn't. passenger side works fine . 3157 bulb and only 2 wires to socket !...


Verify:
- the bulb socket are still wired soundly on the back side
- contacts inside socket are still intact.
- wires are not frayed/broken (entire length)
- the actual bulb is good
-all ground wires are soundly connected

3cf55e8d-23c8-4483-b9ba-2225f93e3a2a.jpg

Oct 11, 2014 | 1997 Ford Crown Victoria

1 Answer

Right front marker light


there is one top screw just remove the one top screw and pull the turn signal and side marker light housing off the fender then replace bulb.

Jan 08, 2013 | 1997 Nissan Pathfinder

1 Answer

Suzuki swift sidelight wont work


It is not clear whether only one lamp is out or more than one. If none of the marker lights are working, check 15A fuse 15 in the junction block. If OK, turn the lighting switch to park to close the light relay. If no results, the light relay or the lighting switch is defective

Oct 22, 2012 | 1997 Suzuki Swift

1 Answer

We need to know the color code on the wires to hook up tail lights to a trailer.


4 way flat molded connectors allow basic hookup for three lighting functions; right turn signal / stop light (green), left turn signal / stop light (yellow), taillight / license / side marker (brown) and a ground (white).brownwire will run both right and left side markers

Oct 23, 2009 | 1997 Nissan Pickup

1 Answer

Had a problem with a right, amber side marker on right side


Usually one of the holes in the marker light where screw goes in, has metal contact where screw meets light, but if not, and they are not push in wire connection type from behind, then just run your white wire up through hole in housing, and bare the end & tighten it up under screw holding light to body. White should be ground, brown should be power.

Jul 02, 2009 | 2004 Dodge Ram 2500

1 Answer

Right side of trailer running lights does not work


Usually one of the holes in the marker light where screw goes in, has metal contact where screw meets light, but if not, and they are not push in wire connection type from behind, then just run your white wire up through hole in housing, and bare the end & tighten it up under screw holding light to body. White should be ground, brown should be power.

Jul 02, 2009 | 2004 Dodge Ram 2500

2 Answers

Rear marker lights are out but brake lights work


marker lights and brake lights usually are separated -- they use a two filament bulb -- check bulb first -- sometimes the connections get dirty -- use electrical contact cleaner and spray the connections -- if that doesnt work -- there is a short in the wiring

Mar 14, 2009 | 1997 Ford Escort

1 Answer

Lights not working


The fuse box is on the driver side when you open the door it's right there on the side of the dash.

Nov 14, 2008 | 1997 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...