Question about 1985 Nissan 300ZX

1 Answer

300ZX 1985 Clutch

My clutch pedal is all the way to the floor to disengage clutch.Reverse is most difficult especially after the car has been driven a bit and has warmed up, then it wont go into reverse without grinding.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

It sounds like your clutch master cylinder is not functioning correctly. First i would check the fluid level and then see if there is a leak.

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 nissan 300zx has start signal failure how do you repair the problem


Start signal comes from the clutch engagement switch. When you press the clutch the pedal arm hits a switch and signals the motor to be able to start. Look and see if you have a little rubber piece pushed through a hole on the clutch pedal arm

Mar 18, 2013 | 1985 Nissan 300ZX

1 Answer

Broken clitch cable on 2000 chevy impala...how do u replace it..the wires are broken


see this steps and fix it. God bless you
Clutch Cable Replacement The clutch cable provides a means to "break the drive" between the engine and the wheels. The engine spins constantly, but the wheels do not, so in order to stop a car's wheels without turning off the engine, the wheels have to disconnect from the engine. When the clutch pedal is pressed, the cable disengages the plates, allowing the driver to shift gears or coast without killing the engine.
A failing clutch cable may make the clutch pedal difficult to depress. If the clutch cable fails, the clutch pedal may remain on the floor and not return to its normal position.
To replace the clutch cable, disconnect it from the clutch pedal (usually inside the vehicle) and from the release mechanism or cable attachment that operates the clutch assembly (usually at the transmission beneath the vehicle). A new clutch cable is then installed and adjusted. (The specifics vary according to the vehicle and range from straightforward to very difficult.)

Oct 04, 2012 | Cars & Trucks

2 Answers

Shifter works when car is off, start car and then shifter won't go in gear. if i start vehicle in first with clutch pedal to floor, car starts going forward. mazda miata mx-5 just put new slave cylinder in...


The one item I would suspect is the through-out-bearing not completely disengaging the pressure plate from the fly wheel. If the vehicle is in neutral and you slowly depress the clutch and release it do hear a singing or whining sound? Since you cannot adjust the clutch any more the through-out-bearing is the component which moves the pressure plate from the fly wheel to stop the power from the engine to the transmission. It is difficult to shift when the engine is on because the fly wheel is still engaged and powering your transmission.

Aug 06, 2010 | 1997 Mazda MX-5 Miata

2 Answers

Clutch pedel stuck on floor


The clutch master has blown out

Jan 19, 2010 | 1990 Ford F250

1 Answer

1988 Nissan 300zx shifts real hard or not at all


you may have a weak clutch master cylinder

May 06, 2009 | 1987 Nissan 300ZX

1 Answer

1990 300zx N/T Clutch not engaging properly


Your Friction disk (clutch) is worn out. Have it replaced....might also need pressure plate, but not necessarily.

Apr 13, 2009 | 1990 Nissan 300ZX

1 Answer

Clutch pedal stays on floor when released


check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Feb 21, 2009 | 1985 Toyota Celica Supra

1 Answer

Clutch pedal fades after repeated clutching - 98 Forester


if the pedal got lot of play if its hydrolique air in the system or missing oil brake fluid goes in the reservoir pierre

Dec 13, 2008 | 1998 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...