Question about 1994 Mercury Tracer

1 Answer

Lower controll arm?

I have a 1994 mercury tracer trio 1.9 there is a part that goes from the inner side of the wheel connected to the wheel some how and the other end is connected to the frame, it is in two pieces, this is the passanger side, the one on the driver side is one single piece, can you tell me what these parts are called. this is on the rear of the car,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 6,674 Answers

Check this link & click on the picture to enlarge it to see if same & name.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008dfd8

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set nonadjustable camber?


all wheel alignments have a camber adjustment
for vehicles with a strut suspension it is in the 3 or 4 bolts that hold the top bush/(rubber mount ) on the inner guard
Those bolts are not concentric but if moved around 1 hole setting at a time will alter the camber and castor of the alignment
If there is insufficient adjustment there , then there is a lower arm or control rod out of adjustment
on many cars with strut suspension that arm that goes from the body to the lower control arm will also affect the wheel alignment , especially if the rubber mounts are bad
have it checked by an accredited specialist suspension shop

Jan 02, 2016 | Hyundai Motor 2003 XG350

1 Answer

I replaced the starter on a 1994 Mercury Tracer now I am getting a continuous hot feed when the key is in the on position. Need help troubleshooting the problem


Sounds like you may have a bad starter relay, possibly shorted out..what you want to do is locate the relay, under hood on one of the inner fenders, follow the positive battery cable to find it.you should only have power from battery cable connection.pull the small red and black wire off, and test for power on that wire with key on, test while wire is fisconnected.you should only have power there when you try to start the engine. Get back to me after you check this

Mar 22, 2014 | 1994 Mercury Tracer

1 Answer

Low idle 95 mercury tracer


The fuel filter on a 1995 Mercury Tracer Trio is on the firewall closest to the bottom of the driver's side. If you're looking at the engine from the front of the car you'll see the battery. $6.85 is the average price for a fuel filter.----------------------------------------------------------------------------------------------
Motorola 711 Programmer

Mar 23, 2013 | 1995 Mercury Tracer

1 Answer

How to install rear struts on a 1999 llexus


selectachapter.gif

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

Print


Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

7923lgb6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
  2. Adjust the parking brake.
  3. Stabilize the suspension as follows :
    1. Install the wheel(s).
    2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
    3. Raise the vehicle.
    4. Remove the wheel.
    5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.

  4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
  5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
  6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).

    Rear tire and wheel assembly

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.


    Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel

  1. Before servicing the vehicle, refer to the Precautions section.
  2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
  3. Remove or disconnect the following:

    Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
  4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
  5. Remove or disconnect the following:

    Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
  6. Place matchmarks on the adjusting cam and body.
  7. Remove or disconnect the following:

    Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
  8. Secure the axle carrier in a vise.
  9. Remove or disconnect the following:

    Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal

    0996b43f802092da.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (inner)-LS 430

  10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
  11. Remove or disconnect the following:

    Axle hub

    0996b43f802092db.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub

    0996b43f802092dc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle

    0996b43f802092dd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing


To install:
  1. Install or connect the following:

    New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.

    0996b43f802092de.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (outer)-LS 430
    Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.

    0996b43f802092e0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (inner)-LS 430
    New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable

  2. Lower the vehicle and turn ON the air suspension switch.



0996b43f80207fdc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear carrier assembly, hub and bearing-

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    WARNING Be careful not to damage the boot and ABS sensor


    Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier


    Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly

To install:
  1. Install or connect the following:

    4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
  2. Inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
  3. Press the hub out of the wheel bearing, then remove the backing plate.
  4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.
  1. Installation is the reverse of the removal procedure, while using the following torque values:

    Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)



0996b43f80208026.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor

To install:
  1. Install or connect the following:
    NOTE Inspect bearing back lash and hub deviation


    Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire


    Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
  2. inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal


Stabilizer Bar

Removal & Installation

  1. Remove the rear wheels.
  2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
  3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
  4. Remove the stabilizer bar.

To install:
  1. Install the stabilizer bar.
  2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
  3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
  4. Install the rear wheels.
  5. Inspect and adjust rear wheel alignment.


Strut & Coil Spring

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.


    No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
  3. Secure the strut in a vise.
  4. Compress the coil spring
  5. Remove or disconnect the following:

    Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Dec 26, 2011 | 1999 Lexus ES 300

1 Answer

What is the timing for a 1994 mercury tracer trio. i belive i have to replace the timing belt and the water pump. im not sure tho bc the feul cut off came on first than after i filled it up it went off. im...


First check to make sure the fuel shutoff is still on. When the engine jumps timing it is usually caused by either the water pump bearings went bad and seized or fell apart. The other is when the belt is old or excessively worn and breaks. Timing marks are dependent on engine size. 1.9 engines have single cam and all marks point straight up. 1.8 is more detailed depending on if it has 1 or 2 cams.

Oct 03, 2011 | 1994 Mercury Tracer

1 Answer

How do I remove the turn signal/light switch from a 94 Mercury tracer.


TURN OFF RADIO FIRST TO KEEP FROM LOCKING IT OUT.DISCONNECT NEGATIVE BATTERY CABLE WAIT 20 MINUTES FOR AIRBAG TO DISCHARGE THEN.REMOVE STEERING WHEEL COVER RETAINING SCREWS FROM THE BACK SIDE OF THE STEERING WHEEL AND REMOVE THE COVER.DISCONNECT THE HORN ELECTRICAL CONNECTOR AND THE SPEED CONTROL ELECTRICAL CONNECTORS IF EQUIPPED.REMOVE THE STEERING WHEEL MOUNTING NUT OR BOLT.YOU NEED A STEERING WHEEL PULLER TO REMOVE STEERING WHEEL DONT USE A HAMMER ON STEERING WHEEL BECAUSE IT WAS FACTORY MADE TO COLLAPSE DURING A CAR ACCIDENT.IF HIT STEERING WHEEL WITH HAMMER IT WILL COLLAPSE.USE STEERING WHEEL PULLER YOU CAN BUY ONE AT SEARS AUTO TOOLS OR SNAP ON TOOLS ALSO MOST AUTO PARTS STORE CARRY IT ALSO.OKAY AFTER REMOVING STEERING WHEEL.REMOVE THE 4 RETAINING SCREWS FROM THE STEERING COLUMN LOWER COVER AND REMOVE THE COVER REMOVE THE UPPER COVER.DISCONNECT THE 3 MULTIFUNCTION SWITCH ELECTRICAL CONNECTORS.REMOVE THE MULTIFUNCTION SWITCH RETAINING SCREW PULL THE ELECTRICAL CONNECTORS FROM THE RETAINING BRACKETS AND REMOVE THE SWITCH.INSTALL EVERYTHING VISA VERSA.TORQUE STEERING WHEEL MOUNTING BOLT TO 34 - 46 FT LBS.

Oct 15, 2010 | 1994 Mercury Tracer

2 Answers

What is the bar or rod called that is on the drivers side hooked to the lower controll arm and goes towards the front it has bushings in it were it connects to the lower controll arm- thoes bushings are...


The rods that connect the K-member (subframe) to the lower control arms are called "strut rods". Your local auto parts store should carry the bushings.

Dec 02, 2009 | 1997 Ford Thunderbird LX

2 Answers

Do u know where my release pin is on my 1994 mercury tracer cause i cant find it? I found my release on my grand marquis but not the tracer!


I pretty sure on this model you have to remove the steering wheel and there is a lock screw inside the column. Hope this helps

Nov 28, 2009 | 1994 Mercury Tracer

1 Answer

Need to replace the lower control Arm. Is there a procedure available?


Please be mindful to carefully note the position of the old parts as you disassemble the suspension, then follow these steps to do the re-installation:

REMOVAL

1. Disconnect the negative battery cable.

2. Raise and safely support the vehicle.

3. Remove the wheel and tire assembly.

4. Remove and discard the tension strut-to-control arm nut, then pull off the dished washer.

When separating the control arm from the steering knuckle, do not use a hammer. Be careful not to damage the ball joint boot seal.

5. Remove and discard the control arm-to-steering knuckle pinch bolt. Using a small prybar, spread the pinch joint slightly, then separate the control arm from the steering knuckle. A drift punch may be used to remove the bolt, but be very careful not to damage the ball joint boot seal.

Do not allow the halfshaft to move outward, or the tripod CV-joint internal parts could separate, causing failure of the joint.

6. Remove and discard the lower control arm inner pivot bolt and nut.

7. Remove the lower control arm from the frame and the tension strut.

INSTALLATION

Make sure the front washer is at the strut-to-lower control arm attachment.

8. Insert the strut into the inner bushing.

9. Position the lower control arm into the subframe bracket, using a new nut and bolt. Tighten to 73-97 ft. lbs. (98-132 Nm).

10. Assemble the lower control arm ball joint stud to the steering knuckle, making sure the ball stud groove is positioned properly. Be very careful not to damage the lower control arm seal.

11. Insert a new pinch bolt and nut, then tighten to 40-53 ft. lbs. (53-72 Nm).

12. Clean the strut threads to remove dirt and/or debris.

13. Install the dished washer, with its dished side away from the control arm bushing. Install a new nut on the strut and tighten to 73-97 ft. lbs. (98-132 Nm).

14. Install the wheel and tire assembly, tightening the lug nuts to 85-105 ft. lbs. (115-142 Nm), then carefully lower the vehicle.

I hope this helps.

Aug 17, 2009 | 1994 Ford Taurus

Not finding what you are looking for?
1994 Mercury Tracer Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...