Question about 2005 Nissan Quest

Open Question

Where's the Egr valve located on a Nissan Quest 2005?

I need to change the Egr valve on my Nisaan Quest 2005 and i don't know where is located?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 255 Answers

SOURCE: egr valve

Hi,the egr valve is located at the intake manifold ,you will see it when you open the hood , it looks like a little space ship, when you get the new one you will have no problem finding it,it is bolted with two bolts and is very easy to install, good luck.

Posted on Aug 24, 2008

Ad
BCally1
  • 133 Answers

SOURCE: How do I change a EGR Valve on a 2005 Dodge Magnum STX w/3.5 engi

its a pain in the *** but it located on the right rear (pass. side) of the motor. it bolts to the cylinder head and runs up to the intake manifold

Posted on Jan 09, 2009

  • 1596 Answers

SOURCE: 2005 Dodge 1500 code p0404 EGR valve.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

  • 323 Answers

SOURCE: EGR Location

On the left side at the rear of the engine, and it isn't fun to change.

Posted on May 29, 2009

cshubart
  • 146 Answers

SOURCE: how do i change my transmission fluid on a 2005 nissan quest

should be a drain plug on tranny pan if changing it is easier to pull pan and change filter if not just have the fluid flushed less mess way easy

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't seem to locate the blower motor resistor for my 2005 Nissan quest.can you help me?


normally in the blower motor enclosure as it uses air flow to help cool the resistors

Mar 23, 2013 | Cars & Trucks

1 Answer

P 1401 location


Codes don't have a certain location, a code means a problem has occurred in a system of the electronics of the cars fuel control or emission control system.
P1401 NISSAN - EGR Temperature SensorPossible causes- EGR Temperature Sensor harness is open or shorted
- EGR Temperature Sensor circuit poor electrical connection
- Faulty EGR Temperature Sensor
- Malfunction of EGR function, EGRC-BPT valve or EGRC-solenoid valve
- Blocked EGR passages When is the code detected?An excessively low voltage from the Exhaust Gas Recirculation (EGR) temperature sensor is sent to Engine Control Module (ECM) even when engine coolant temperature is low, or an excessively high voltage from the EGR temperature sensor is sent to ECM even when engine coolant temperature is high.
P1401 NISSAN Description The Exhaust Gas Recirculation (EGR) temperature sensor detects temperature changes in the EGR passage way. When the EGR valve opens, hot exhaust gases flow, and the temperature in the passage way changes. The EGR temperature sensor is a thermistor that modifies a voltage signal sent from the Engine Control Module (ECM). This modified signal then returns to the ECM as an input signal. As the temperature increases, EGR temperature sensor resistance decreases.
This sensor is not used to control the engine system. It is used only for the on board diagnosis

Oct 08, 2012 | 2000 Nissan Maxima

1 Answer

What is a b p t valve


Back Pressure Transducer Valve, part of the EGR system. The valve monitors and restricts too much exhaust pressure into the intake manifold from the Exhaust Gas Recirculation valve. Vacuum to the EGR valve is first routed through the BPT valve. I unhooked it on my '79 Datsun, don't know how important it is for EGR operation, did not affect operation of the engine.

Oct 06, 2012 | 1996 Nissan Pickup

1 Answer

2000 Nissan Quest AC problem


Yes it's very true, change the front one and you will not have any further problem

If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_2094e122cc46f24c

Sep 27, 2017 | Nissan Quest Cars & Trucks

1 Answer

My 1997 Nissan Quest Van when I start it it's okay, but when I accelerate the gas it starts to sputter. These miniture backfires go on but when I release the gas pedal the sputtering stops. I am n


the first thing I would start with is looking for vaccume leaks. be sure to check your EGR valve, then move to your MAP sensor. The next thing that it could be is a stopped up catylic converter

Apr 29, 2012 | Nissan Quest Cars & Trucks

1 Answer

High pitched beep coming from somewhere on the outside of the 2005 Nissan Quest minivan.


Worn brakes or a dry wheel bearing could be the cause. If you don't know how much wear is left on your brake pads, have them checked.While the brakes are being checked, have the wheels turned by hand and listen for the bearings to see if they are the cause.

Aug 06, 2011 | 2005 Nissan Quest

1 Answer

I have high emission on my 1998 nissan quest how do I get it down to pass smog


Hi there

There are a few ways you can do this:

Use ultra-low sulphur fuel (not sure if the US has this but the UK does).

Change or clean out the air filter (check my profile for a how-to)

Make sure the EGR valve is connected up properly. This is the exhaust gas recirculating valve, located on the intake manifold. Unbolt is, clean it out with a wire brush and carb cleaner, refit.

Get the Nissan checked again, if it is still high, the catalytic converter could be due a change, especially as it will be 12 years old.

Hope this helps, please vote if so. Thanks :)

Jul 13, 2010 | 1998 Nissan Quest

Not finding what you are looking for?
2005 Nissan Quest Logo

Related Topics:

882 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

83951 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...