Question about Mitsubishi Passenger

2 Answers

VR-4 Auto 1996/97 with spongy brake pedal - Passenger Mitsubishi Cars & Trucks

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

There is air in the break lines find the bleeders on the brake calliper pump the breaks 5 times hold petal,, open the bleeder do not let the pedal up before closein the bleeder! once you open the bleeder the pedal will hit the floor brake fluid will come out with the air repeat this until you get a steady stream of fluid with no air. start this process at the passenger rear wheel,drivers rear, front passenger, front drivers this is a 2 man job!

Posted on Sep 29, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

If you have not fitted brake pads to it [as these can take time to bed in ] and give the pedal a soft and extra travel feeeling you have air in the brake system the simple check to do is look behind all your wheels see if you can see brake fluid sepping down the back plates or any damp patchs which would inply there is a problem if not pick your bonnet up have a look around your master cylinder to see if theres any sign of a leak that was the easy bit if you can,t see anything you will have to take the wheels off to find out what is leaking don,t forget if you change one of the seals or calipers or cylinders on that axle change the other side yates210456

Posted on Sep 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My brake pedal is spongy, what would cause that? fluid level is good


air in the line or bad booster. try getting the brakes bled if it doesnt fix it probably a bad booster

Jun 26, 2012 | 2005 Dodge Ram 2500 Truck

2 Answers

Spongy brake pedal apears to be leaking fluid from brake booster


check or adjust brake pedal, check brake booster or replace new one, check pedal return spring and bushing, check all wheel cylinder or replace, check brake shoe or brake pad, check brake fluid or replace,.

Apr 03, 2011 | 1999 Pontiac Sunfire

1 Answer

2003 rav 4, just replaced front calipers and pads, after bleeding the line,peddle was spongie, bled all four lines, peddle still spongie, do I need the engine running to properly bleed the lines, and since...


I would bleed the rears too especially if the brake fluid reservoir drained empty. Also you may need to drive the vehicle to seat the brake pads. Check and see how the pedal feels initially before you road test to make sure you don't need to pump the brakes in order to stop. if you do then re bleed all four wheels.If you don't have to pump the pedal and it just feels spongy then try going around the block a few times and see if the pedal stiffens up after the pads have seated.

Oct 11, 2010 | 2003 Toyota RAV4

1 Answer

Spongy brake pedal on 2003 Frod escort zx2.


loosen of the hand-brake adjustment and press the brake pedal a few times to self adjust the rear brakes.
Re-tighten the handbrake adj last.
Front brake sounds like a seized caliper,If possible remove caliper and clean and lubricate the piston.
This may work but replacement caliper may be the only other solution.Make sure the caliper slides are also clean and lubricated and the brake pads are in good order.(TRY THIS FIRST)
Also new brake shoes can make the pedal feel spongy for a couple of hundred miles until they have been run in.

Jul 04, 2010 | 2003 Ford ZX2

1 Answer

87 jag xj6. Brake pedal spongy goes all the way


If the brake lines and fluid is clear then you may have to look at the brake booster found at the other end of the brake pedal under the hood...

Jul 23, 2009 | 1987 Jaguar XJ6

2 Answers

Spongy brake pedal


I have a 2001 Chevy 1500 4 X 4 that recently had all new pads, rotors, and calipers installed. Since then my brake pedal goes almost to the floor before I get any brakes. I took it back to the shop and they bled the brakes with no better results. I bled them also with no results. I took the truck back and they installed a master cylinder with no results. It's now at the Chevy dealer and they say it's normal - BS! I had good brakes before I had all of the brake parts replaced, no one can figure it out. If you have a load in the truck or if you tow anything you better be looking at the ditch to avoid an accident. The original brakes would put you nose into the windshield and now I could stop it better the Fred Flinstone way. Anyone have an answer????????

Jun 18, 2009 | 1998 Chevrolet C1500

1 Answer

Brake pedal is spongy


how did you bled them back 2 front?

Mar 27, 2009 | 1989 Ford F 150

1 Answer

SPONGY BRAKE PEDAL


spongy brake pedal indicates air in the system... have the brakes inspected for leaks as it leaks when you apply the brakes and sucks in air when you release them.

Robert

Dec 17, 2008 | 2008 Toyota Camry

1 Answer

Ford Bronco II spongy brake pedal


if the booster is bad the pedal would be hard sounds like the e-brake is stuck take off the drums and make sure the arms are all the way back then did you adjust the rear brakes after changing the shoes

Dec 14, 2008 | 1989 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...