Question about 2003 Hyundai Accent

1 Answer

Replace liscense plate light?

Lights are out We have taken the back apart and still no access to lights. they are held with 2 screws each but no access to get to it. Do we remove the "dome" how is it held in place

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

Hi if memory serves? you remove the panel on inside of hatch then the lamp/s cover is secured with 10 mm hex nuts when cover lifted off the access to bulbs are apparent to see hope this helps?

Posted on Oct 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get to the license plate bulb for a 2004 nissan sentra


There are 2 bulbs above the license plate, each under a plastic cover. The covers are held in with 2 screws each. Just unscrew and remove the plastic covers and you should be able to access the bulbs.

Mar 21, 2014 | 2004 Nissan Sentra

2 Answers

Change the license plate lights in my 2002 buick rendezvous cx


On most GM cars, SUV's, and light duty trucks, the license plate light bulbs are held in place by 2 screws...located on each side of the plastic lens...remove these 2 screws then wiggle the entire assembly out so you can view and replace the bulbs...Again most GM cars have 2 bulbs also...Hope this helps.

Sep 06, 2013 | 2002 Buick Rendezvous

1 Answer

How to change liscense plate bulb


it`s very simple-- above lic. plate you will see the light lens. There may be 2 phillips screws, if there are just remove them and use a small flat head scewredriver to pop it open. Then remove the ``penut`` bulb. If there are no phillip screws, then use the flat head to pop the lens.
Also before you start lift the trunk open and see if you can access the bulbs from in there.
Good luck-it is very simple..

Feb 25, 2011 | 2003 Pontiac Sunfire

1 Answer

How do I change the front side marker light bulbs?


Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs
  • Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.
  • 2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.
  • 3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.
  • 4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.
  • 5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.
  • 6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.
  • 7 Replace the screws along the edge of the fender liner.


  • Dec 04, 2010 | 2006 Porsche Cayenne

    1 Answer

    How do you replace the rear liscense plate lights


    Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

    Apr 06, 2010 | 1998 Ford Explorer

    1 Answer

    How to change liscense plate light? se model


    hi, if your license plate bulb cover has no screw holes in it then the chances are its just pushed in it may be a very tight fit but should just pull out its usually held in by two plastic clips that lock once its pushed in so using a screw driver to lever the light cover off should get it off.

    If you have a cover on the inside of the boot that covers the wires going to the number plate bulb you may be able to take this off and then be able to see how it comes off.

    Let me know how you get on or if you need further assistance ok

    Dec 28, 2009 | 1997 Nissan Pathfinder

    1 Answer

    Tag light replacement 98 ford taurus


    I believe the tag lamp covers are held on by phillips screws. Remove screws and should be able to replace bulbs. Goodluck.

    Nov 12, 2009 | 1998 Ford Taurus

    3 Answers

    No backup lights and no light over the liscense plate where is the fuse located


    Depending on your make the fuse panel is in 1 of 3 places....

    1. When you open the driver side/passenger side door theres a pannel you have to remove, It may or may not say Fuses

    2. Under the dash on the driverside behind the foot pedals

    3. Under the hood (drivers side)

    also being all the lights that are malfunctioning are in the rear (breaklights, tail lights and LP lights) after you check your fuses if the problem is still there, check the ground cable from the tail lights, if it was pulled/severed/or rusted apart this will have the same symptoms

    Sep 27, 2009 | 1996 Ford Contour

    2 Answers

    Need to fix lights on number plate on 1.3 3dr gl


    hi from uk the number plate lights x2 are on same fuse as side+tail lights so if n/plate is not lit ?more likely bulbs have blown ? to access remove the panel from boot lid (clips+screws) then you will see rear of n/plate lights the bulb holders twist anti clock slightly and pull out replace bulbs with same type 5watt check all work b4 refitting panel

    Feb 05, 2009 | 1999 Hyundai Accent

    Not finding what you are looking for?
    2003 Hyundai Accent Logo

    79 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    70347 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6876 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...