Question about 1987 Jeep Wrangler

1 Answer

Front axle4x4 my4x4 wont desingage to drive in 2wdrive .the trans shifts ok and when i drive it in 4x4 its ok iy just wont go out of 4x4 to 2wd can anyone help me iam thinking it might be vacume but iam gettint good vacume to front diff switch . could it be the vacume vavle as fault ? help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Yes but take valve out and clean most likely there is debri in the valve take of and spray with either se if it works

Posted on Sep 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 Ford Ranger grinds in drive and 1st, and 2nd but nothing else and wont drive but will in reverse, what could cause this?


I'm guessing you have a automatic trans? if it is a 4x4 make sure you are in 2wd or 4x4 all the way if so you need a trans shop it won't be an easy fix

Jan 12, 2013 | Cars & Trucks

1 Answer

4x4 K1500 Chevy Truck, 4 wheel drive repair instructions


There are a number of different hub systems so this may not work but it has worked for me on both auto and manual locking hubs. On a flat surface without traffic. Put the trans into neutral, shift the transfer case into 4x4, shift the trans into reverse and back the truck up 15-20 feet. Completely stop and shift trans into drive. See if this has locked the hubs in. If not, you can also try following the same instructions except shifting into 4wd low. Sometimes the hubs need a "bump" to get them to slip into place. Keep In mind that if the 4 wd low select works, you need to shift it back into 4 wd high before continuing! When taking the truck out of 4wd to 2wd, I recommend the same, shift to neutral, select 2wd, back truck up, shift back to drive and check. Its entirely possible that your hubs need maintenance (they're often overlooked) but hopefully this will get you going. Please let me know if thus worked or if I can offer other suggestions. Good luck!

Jan 18, 2012 | Chevrolet 1500 Cars & Trucks

1 Answer

Can some explain the proper way to shift from 2wd


4wd auto: you can shift into this mode at anytime. it is good for conditions where you might need 4wd.
4wdhi:: you can shift into this at speeds up to 30mph and both of these back to 2wd while in gear.
4wd lo : stop vehicle and shift truck into nuetral ok to be rolling around 3mph shift into 4lo then put in gear same when shifting back to 2wd

Feb 19, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

Ford excursion 4x4 locks and wont unlcock


my4x4 is stuck and can't change back to 2w drive

Feb 09, 2010 | 2001 Ford Excursion

2 Answers

1998 Ford f150 4x4 intermittant clapping sound front axle area


The vacuum shift motor ( actually a diaphragm ) is a vacuum to move the lever one direction ( i.e. 4WD ) and then vacuum to move the other direction ( i.e. back into 2WD ).

You can shift into 2WD and remove the vacuum lines and plug them to remove this, if you think the vacuum shift solenoids are getting ground from another source and shifting the front axle, or just unplug the connector on the shift solenoids. The GEM activates the Shift solenoids by applying ground to them.
1b857e9.jpg

I would have to agree with papa_11069 that the problem is in the front u-joints.

Dec 30, 2009 | 1998 Ford F150 Regular Cab

1 Answer

In 2WD but 4x4 light on also front axels and hubs stay engaged


youve probably have got a bad hub. with an open front differintial it will spin the tires in the air but not when torgue is applied.

Nov 20, 2009 | 2005 Ford F-150

1 Answer

95 ram 2500 4x4 wont shift into od


ckeck linkage they might have undone iy and not put back in right place

Nov 02, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

The part time light is on


start car put it in neutral shift 4x4 lever into 4x4 low then drive a few feet. now shift main trans back to neutral then move 4x4 shifter back to 2wd high for normal driving then shift in drive and drive for a few min light should turn off..if nor disconnect battery for 15 min to reset computer and see if that does it. if that doesnt work you may need 4x4 linkage adjusted ..do you have a lift?

Nov 27, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...