Question about 2003 Ford F150 Regular Cab

1 Answer

Wheel baring i have a 2003 f150 4x4 lariat that the baring s bad and i was woundering if it is hard to change that out or if there is speciel tools or if there are parts that have to be pressed or so forth i know this is not a trouble shooting ? or if there was a diagram i could folow or something like that wwith out buying a whole book

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

This brg is a sealed brg. it the special tools you need is the one that takes off the nut on the axle shaft and there is 4 bolt that hold the brg in place then you have to pull the brg out .
stop by a auto parts store and look at the brg assembly .
that will give you a good idea.
its not a hard job.
good luck

Posted on Sep 28, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

After changing the passenger side caliper and bleeding the brakes my f 150 still doesnt have brakes. whast would be thet best thing to check for?

Without a full diagnostic set of gages, it is hard to say. I am betting the seals in the master cylinder are shot.

Mar 28, 2017 | Ford Cars & Trucks

1 Answer

Anti-lock function on brakes is triggered by applying brakes while steering wheel is turned hard over

Sounds like you are losing wheel speed signal when under hard turns. This is commonly caused by the harness at or near the wheel speed sensor has a bad connection of there may be a break in the wiring that intermittently loses signal to the ABS module and causes the anti-lock function to happen, (loss of wheel speed is like wheel skid as far as the ABS module is concerned) It is usually necessary to have a scan tool to monitor the data and read codes on the ABS system. You may have to take vehicle to shop that is capable of diagnosing the problem.

Oct 13, 2015 | 2003 GMC Sierra 1500

1 Answer

4 wheel drive will not activate on 2003 f150

Sounds like the module went bad.
Easy fix is to go to auto zone let them pull the codes for free and they can give you the part or they will even put it in for you.

Aug 20, 2012 | Ford Cars & Trucks

1 Answer

2003 bmw z4 - high beams (halos) do not come on when steering wheel wah is push forward to the high beam position...yet they do come on when the wan is pulled back to the "flash" position....bad...

Bad dimmer switch. To be honest - it's a pain in the #$%. Air bag and wheel need to be removed. I'd had dealer or competent BMW shop do it.

Mar 31, 2011 | BMW Z4 Cars & Trucks

1 Answer

Kia carnival timming belt change

petrol or diesel ?? diesel do not do it yourself as a lot of speciel tools needed

Oct 08, 2010 | Kia Sedona Cars & Trucks

4 Answers

What is the recomended mileage to replace front wheel bearings on a 1999 chevy malibu

None you replace if noisey or excessive end play seale & maintenance free

Aug 30, 2009 | 1999 Chevrolet Malibu

1 Answer

2003 ford f350 lariat crew cab drw speedometer not working

Jul 09, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

2003 golf diesel headlights butn out regularly

1 : either the bulbs are being touched by bare skin durring install <oils in skin will ruin the bulbs life> or you may have a bad connection .when replacing next make sure connector at back of bulb isnt melted or even "hot" looking if so replace pigtail. 2 : not a real easy way to replace but main thing is to not touch new bulb with skin.

Mar 22, 2009 | 2003 Volkswagen Golf

3 Answers

Replacing front wheel bearing

those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Aug 28, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Ford F150 Regular Cab Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides