Question about 1998 Chevrolet S-10 Pickup

1 Answer

Window Crank How do you take the Window crank off of the interiror door panel?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

Theres a special tool you need for removing the c-clip from behind the handle

Posted on Sep 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 impala back window stuck down


You checked fuses and relays for electrical cranked window?
Remove: internal door handle, remove window crank if manual crank, door panel, remove film/paper seal.
If is mechanical crank: check for worn out parts on gearing and racks (reinstall crank and wind window up and down). Replace worn parts.

If electrical window crank: check for power at solenoid. Try switch again and watch to see if solenoid engages and tries to crank.
Check to see if switch is broken. Try door switch and drivers door switch.
Pickup another solenoid and replace old one.

Apr 30, 2014 | Cars & Trucks

1 Answer

How do I fix a window that wont go up in a 1998 ford mustang?


I'm assuming it's not power window's,you will have to remove to window crank and the door opening latch,on the window crank,there's a clip embedded into crank,you can push door panel in at crank and use a flat head screw driver to push clip off,door handle has to come off,arm rest if you have one,,there are clips holding the panel to door,you can also use a flat head to put in between panel and door and pop loose,you may have to replace clips.After you get panel off ,you will see why the glass won't come up,may be off track.

Aug 10, 2012 | Ford Mustang Cars & Trucks

1 Answer

Remove the interor of the door


To remove window crank handle,

pull the handle toward you exposing the

window crank handle retaining clip on the

back side of the window crank handle. Using

your trim panel removal tool, apply pressure

to the window crank handle retaining clip to
remove the crank handle.

Aug 09, 2012 | 2005 Kia Spectra

2 Answers

Door panel removal


To remove the window crank slip a small standard screwdriver behind where the crank mounts to the door.There is a small spring like c-clip pop the clip off and cran Window Handle Operation:
00457_window_handles.jpgReplacement handle for cranking or rolling a side or rear window up or down. It slides over the window crankshaft and uses splines to match the window crank shaft splines as to avoid slippage. It's held in place with a simple spring clip and come in a variety of styles and colors.k will come off.

Jun 27, 2012 | 1994 Suzuki Swift

3 Answers

How do I take the window handle to get the door panel off?


there is a C clip that slides over window crank locking it on to the window crank shaft. A strong tool like a dentist pik that has a hook on it works great !! Or a small long flat screw driver, push in on the door panel by the window crank and look between crank and door panel, you will see this clip on the back of handle. push or pull this clip off the handle and the handle will pull off the window crank shaft. keep an eye on this clip as it like to take flying lesson.( wear safety glasses.) When installing clip, install on window crank in the slits or grooves and just push handle onto crank rod. you might have to hit with rubber mallet (TAP TAP ) make sure it locks on.

Jan 14, 2011 | 1993 Nissan Pickup

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

Need a diagram of how the door panel comes off of a 95 chevy blazer. I need to remove the door panel to fix the lock assembly. Need to know if there are clips at the bottom of the door, or just the screws.


There will always be clips attached to the panel from the inside-after screw removal and window crank removal (window crank on mostly earlier models) You can start at a bottom edge with what i recommend a door panel removal tool-most auto parts store carry these. even if a clip falls out you can reinsert it.Also the door removel tool doubles as a window crank clip remover.

Sep 20, 2009 | 1995 Chevrolet Blazer

1 Answer

Removing door panel of manual crank 2000 VW Beetle


Your window crank is held on by a clip at the base of the crank handle. You need a small hook (kind of like a knitting needle) to get behind the base and pull the clip off of the crank.

I hope this helps you, and I wish you luck on your repair.

May 13, 2009 | 2000 Volkswagen Beetle

1 Answer

Trying to remove the door panel to get to the lock mechanism but dont know how to remove the window crank handle


Push the door panel in gently and there will be a clip behind the window crank handle. Remove the clip and the window crank will come off the splined shaft. The clip will be in a half circle around the spline shaft.

Jul 25, 2008 | Jeep Wrangler Cars & Trucks

1 Answer

Door Panels


There's a small wire clip right behind where the door panel meets with the crank. Its really hard to see. I had to pry the crank a bit with a screw driver to see it. Anyway, when you do see it there's a part that protrudes more than the rest, and you can slide a screw driver back there and pry it out.

Jul 12, 2008 | 1994 Mercury Tracer

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...